Intervertebral fusion surgery for spinal trauma, degeneration, and deformity correction is a major vertebral reconstruction operation. For most cages, the stiffness of the cage is high enough to cause stress concentration, leading to a stress shielding effect between the vertebral bones and the cages. The stress shielding effect affects the outcome after the reconstruction surgery, easily causing damage and leading to a higher risk of reoperation. A porous structure for the spinal fusion cage can effectively reduce the stiffness to obtain more comparative strength for the surrounding tissue. In this study, an intervertebral cage with a porous gradation structure was designed for Ti64ELI alloy powders bonded by the selective laser melting (SLM) process. The medical imaging software InVesalius and 3D surface reconstruction software Geomagic Studio 12 (Raindrop Geomagic Inc., Morrisville, NC, USA) were utilized to establish the vertebra model, and ANSYS Workbench 16 (Ansys Inc., Canonsburg, PA, USA) simulation software was used to simulate the stress and strain of the motions including vertical body-weighted compression, flexion, extension, lateral bending, and rotation. The intervertebral cage with a hollow cylinder had porosity values of 80–70–60–70–80% (from center to both top side and bottom side) and had porosity values of 60–70–80 (from outside to inside). In addition, according to the contact areas between the vertebras and cages, the shape of the cages can be custom-designed. The cages underwent fatigue tests by following ASTM F2077-17. Then, mechanical property simulations of the cages were conducted for a comparison with the commercially available cages from three companies: Zimmer (Zimmer Biomet Holdings, Inc., Warsaw, IN, USA), Ulrich (Germany), and B. Braun (Germany). The results show that the stress and strain distribution of the cages are consistent with the ones of human bone, and show a uniform stress distribution, which can reduce stress concentration.

Banana (Musa sp.) is cultivated worldwide and is one of the most popular fruits. The soil-borne fungal disease Fusarium wilt of banana (FWB), commonly known as Panama disease, is caused by Fusarium oxysporum f. sp. cubense (Foc) and is a highly lethal vascular fungal disease in banana plants. Raman spectroscopy, an emerging laser-based technology based on Raman scattering, has been used for the qualitative characterization of biological tissues such as foodborne pathogens, cancer cells, and melamine. In this study, we describe a Raman spectroscopic technique that could potentially be used as a method for diagnosing FWB. To that end, the Raman fingerprints of Foc (including mycelia and conidia) and Foc-infected banana pseudostems with varying levels of symptoms were determined. Our results showed that eight, eleven, and eleven characteristic surface-enhanced Raman spectroscopy peaks were observed in the mycelia, microconidia, and macroconidia of Foc, respectively. In addition, we constructed the Raman spectroscopic fingerprints of banana pseudostem samples with varying levels of symptoms in order to be able to differentiate Foc-infected bananas from healthy bananas. The rate at which FWB was detected in asymptomatic Foc-infected samples by using the spectral method was 76.2%, which was comparable to the rates previously reported for other FWB detection methods based on real-time PCR assays, suggesting that the spectral method described herein could potentially serve as an alternative tool for detecting FWB in fields. As such, we hope that the developed spectral method will open up new possibilities for the on-site diagnosis of FWB.

Commercial purity titanium (CP-Ti) and a Ti-6Al-4V alloy (Ti64) were processed by high-pressure torsion (HPT) for 10 and 20 turns. The HPT processing produced a nanostructured microstructure and a significant strength enhancement in the CP-Ti and Ti64 samples. After 20 turns, the samples of HPT-processed CP-Ti and Ti64 were subjected to laser surface treatments in an air atmosphere using different scanning speeds and laser powers. The surface roughness of the laser-modified samples increased with increasing laser power and this produced hydrophilicity due to a lower contact angle. After a holding time of 27 days, these samples underwent a hydrophilic-to-hydrophobic transformation as the contact angle increased from 13° to as much as 120° for the CP-Ti sample, and for the Ti64 sample the contact angle increased from 10° to 126°. In addition, the laser surface modification process was carried out with different atmospheres (air, vacuum and O₂) on heat-treated but unstrained CP-Ti and Ti64 samples and the contact angle changed due to the surface element content. Thus, as the carbon content increased from 28% to 47% in CP-Ti in a vacuum environment, the surface contact angle increased from 22° to 140°. When a laser surface modification process is conducted under oxygen-less conditions, it is concluded that the contact angle increases rapidly in order to control the hydrophobic properties of Ti and the Ti alloy.