Hydrocarbon ionomers bear the potential to significantly lower the material cost and increase the efficiency of proton‐exchange membrane water electrolyzers (PEMWE). However, no fully hydrocarbon membrane electrode assembly (MEA) with a performance comparable to Nafion‐MEAs has been reported. PEMWE‐MEAs are presented comprising sPPS as membrane and electrode binder reaching 3.5 A cm−2 at 1.8 V and thus clearly outperforming state‐of‐the‐art Nafion‐MEAs (N115 as membrane, 1.5 A cm−2 at 1.8 V) due to a significantly lower high frequency resistance (57 ± 4 mΩ cm² vs 161 ± 7 mΩ cm²). Additionally, pure sPPS‐membranes show a three times lower gas crossover (1.1 mA cm−2) in a fully humidified surrogate test. Furthermore, more than 80 h of continuous operation is shown for sPPS‐MEAs in a preliminary durability test (constant current hold at 1 A cm−2 at 80 °C). These results rely on the unique transport properties of sulfonated poly(phenylene sulfone) (sPPS) that combines high proton conductivity with low gas crossover.
Polymer electrolyte membrane (PEM) water electrolysis is a crucial technology for green hydrogen production. Hydrocarbon membranes are drawing a lot of attention due to potentially superior properties and the fact that common fluorinated polymers might face a potential ban. This study introduces a sulfonated poly(phenylene sulfone) (sPPS) membrane, reinforced with a poly(ether‐ether‐ketone) (PEEK) mesh. The reinforced membrane induces a drastic increase in dimensional stability, enabling direct anode casting—an essential step toward industrial manufacturing. It further exhibits a significant reduction in water uptake (115% vs 294% for pure sPPS) and a 40% lower H2‐crossover (0.18 mA cm−2) compared to the industry standard N115 (0.31 mA cm−2). Due to the lower thickness (74 vs 127 µm) and higher ion exchange capacity (IEC)(1.92 vs 0.89 mmol g−1), the PEEK‐sPPS membrane displays a substantially lower resistance (70 vs 159 mΩ cm2 for N115). This directly translates into a voltage reduction of ≈90 mV at 1 A cm−2 or ≈180 mV at 2 A cm−2, both typical operating current densities. Finally, PEEK‐sPPS exhibits the longest lifetime shown for hydrocarbon membranes with almost 650 h at 1 A cm−2 and a low degradation rate (80 µV h−1).
During cell cycling with NCM cathode and Li 6 PS 5 Cl catholyte, interfacial degradation leads to reduced active mass and particle cracking. We mitigate this by coating NCM with polyvinylpyrrolidone and sulfonated poly(phenylene sulfone).
High-molecular-weight AA-BB-type aliphatic polyesters were synthesizedviaCu(I)-catalyzed click step-growth polymerization (SGP) following a new synthetic strategy. The synthesis was performed between diyne and diazide monomers in an organic solvent as one pot process using three components and two stages. The dipropargyl esters of dicarboxylic acids (component 1) were used as diyne monomers, di-(bromoacetic acid)-alkylene diesters (component 2) were used as precursors of diazide monomers, and sodium azide (component 3) was used for generating diazide monomers. The SGP was carried out in two steps: at Step 1 dibromoacetates interacted with two moles of sodium azide resulting in diazide monomers which interacted in situ with diyne monomers at Step 2 in the presence of Cu(I) catalyst. A systematic study was done for optimizing the multiparameter click SGP in terms of the solvent, duration of both Step 1 and Step 2, solution concentration, catalyst concentration, catalyst and catalyst activator (ligand) nature, catalyst/ligand mole ratio, and temperature of both steps of the click SGP. As a result, high-molecular-weight (up to 74 kDa) elastic film-forming click polyesters were obtained. The new polymers were found suitable for fabricating biodegradable nanoparticles, which are promising as drug delivery containers in nanotherapy.