The optimal hybridization of photovoltaic (PV) and thermoelectric (TE) devices has long been considered ideal for the efficient harnessing solar energy. Our hybrid approach uses full spectrum solar energy via lossless coupling between PV and TE devices while collecting waste energy from thermalization and transmission losses from PV devices. Achieving lossless coupling makes the power output from the hybrid device equal to the sum of the maximum power outputs produced separately from individual PV and TE devices. TE devices need to have low internal resistances enough to convey photo-generated currents without sacrificing the PV fill factor. Concomitantly, a large number of p-n legs are preferred to drive a high Seebeck voltage in TE. Our simple method of attaching a TE device to a PV device has greatly improved the conversion efficiency and power output of the PV device (~30% at a 15°C temperature gradient across a TE device).

Printing techniques could offer a scalable approach to fabricate thermoelectric (TE) devices on flexible substrates for power generation used in wearable devices and personalized thermo-regulation. However, typical printing processes need a large concentration of binder additives, which often render a detrimental effect on electrical transport of the printed TE layers. Here, we report scalable screen-printing of TE layers on flexible fiber glass fabrics, by rationally optimizing the printing inks consisting of TE particles (p-type Bi_0.5Sb_1.5Te₃ or n-type Bi₂Te_2.7Se_0.3), binders, and organic solvents. We identified a suitable binder additive, methyl cellulose, which offers suitable viscosity for printability at a very small concentration (0.45–0.60 wt.%), thus minimizing its negative impact on electrical transport. Following printing, the binders were subsequently burnt off via sintering and hot pressing. We found that the nanoscale defects left behind after the binder burnt off became effective phonon scattering centers, leading to low lattice thermal conductivity in the printed n-type material. With the high electrical conductivity and low thermal conductivity, the screen-printed TE layers showed high room-temperature ZT values of 0.65 and 0.81 for p-type and n-type, respectively.

With the rapid development of electronic technology and the integration of electronic chips, electromagnetic wave pollution and thermal management have become two critical issues hindering the growth of electronic equipment. Traditional polymer-based electronic packaging materials have very low thermal conductivity and almost no electromagnetic wave absorption ability. Therefore, the development of polymer-based composites with efficient electromagnetic wave absorption and thermally conductive performances is currently a hot research topic in the field of microelectronic packaging. At present, the addition of thermally conductive and dielectric (magnetic) fillers to the polymer matrix is an effective way to solve this problem. In this review, firstly, we briefly introduce the mechanism of action of electromagnetic wave absorbing materials and thermally conductive materials, respectively. Then, we list the relevant representative fillers which can be used in electromagnetic wave absorption and thermal management and summarize the current research progress of these materials. Finally, we present the current challenges facing the field and prospects for future development. Graphical Abstract In this review, we give a detailed overview of the research progress on the microwave absorption and thermally conductive properties of the composites with different fillers and microstructures.

An average thermal switching ratio of ~8× and maximum switching ratio of ~10× is achieved within a temperature range of 10 K.

Coherent thermal emission deviates from the Planckian blackbody emission with a narrow spectrum and strong directionality. While far-field thermal emission from polaritonic resonance has shown the deviation through modelling and optical characterizations, an approach to achieve and directly measure dominant coherent thermal emission has not materialised. By exploiting the large disparity in the skin depth and wavelength of surface phonon polaritons, we design anisotropic SiO₂ nanoribbons to enable independent control of the incoherent and coherent behaviours, which exhibit over 8.5-fold enhancement in the emissivity compared with the thin-film limit. Importantly, this enhancement is attributed to the coherent polaritonic resonant effect, hence, was found to be stronger at lower temperature. A thermometry platform is devised to extract, for the first time, the thermal emissivity from such dielectric nanoemitters with nanowatt-level emitting power. The result provides new insight into the realisation of spatial and spectral distribution control for far-field thermal emission.