In order to investigate the flow structure and unsteady behavior of three-dimensional corner separation, a delayed detached-eddy simulation (DDES) method based on the Spalart–Allmaras (SA) model is performed on the third-stage stator of a multistage low-speed axial compressor. The stator simulation is validated by experiments before flow mechanism analysis. The complicated flow fields in the stator are then described step by step. Firstly, the structure and development process of vortices in corner separation flow are analyzed. Secondly, the velocity histogram of the monitor points in the mainstream and corner separation regions is obtained, and the velocity distribution of the corner separation region is discussed. Finally, Reynolds stress, Lumley anisotropy, turbulence energy spectra, and helicity density are discussed to understand the turbulence behavior of the corner separation flow in the stator. The results show that the corner separation appears at even the design condition and different kinds of vortical structures appear in the stator hub corner. The unsteadiness of corner separation flow is mainly reflected in the separation on the suction side of the blade and the wake shedding. Turbulence anisotropy and energy backscatter are found to be dominant in the separation region, which is correlated to the high shear stress.
Casing pressure measurements and Stereoscopic Particle-Image Velocimetry (SPIV) measurements are used together to characterize the behavior of the rotor tip leakage flow at both the design and near-stall conditions in a low-speed multistage axial compressor. A three-dimensional Navier-Stokes solver is also performed for the multistage compressor and the prediction of tip leakage flow is compared with SPIV data and casing dynamic static pressure data. During the experiment 10 high-frequency Kulite transducers are mounted in the outer casing of the rotor 3 to investigate the complex flow near the compressor casing and Fourier analyses of the dynamic static pressure on the casing of the rotor 3 are carried out to investigate the tip leakage flow characteristics. At the same time, the two CCD cameras are arranged at the same side of the laser light sheet, which is suitable for investigating unsteady tip leakage flow in the multistage axial compressor. The SPIV measurements identify that the tip leakage flow exists in the rotor passage. The influence of tip leakage flow leads to the existence of low axial velocity region in the rotor passage and the alternating regions of positive and negative radial velocity indicates the emergence of tip leakage vortex (TLV). The trajectory of the tip leakage vortex moves from the suction surface toward the pressure surface of adjacent blade, which is aligned close to the rotor at the design point (DP). However, the tip leakage vortex becomes unstable and breaks down at the near-stall point (NS), making the vortex trajectory move upstream in the rotor passage and causing a large blockage in the middle of the passage.
Turbomachinery has been widely used in the energy systems as an energy conversion device, such as gas turbine and aero-engine. The losses in the turbomachinery, especially in the multi-stage conditions, restrict the energy conversion efficiency and corresponding fuel economy. Previous studies show that non-axisymmetric endwall could be used to decrease the losses in compressors, but the real effects in the rig tests are usually inconsistent with the numerical simulation. In this paper, a shroud profiled endwall optimization method with the strategy of local loss as the objective function is proposed, aiming at reducing the tip loss of an embedded stator under the operating point. The traditional total loss coefficient and four local loss functions are studied to investigate how the objective functions influence the optimization results. Three optimized endwall geometries are tested in the embedded test platform. It showed that the strategy of loss coefficient above 90% span as the objective function was best at decreasing the stator loss in the tip region as well as the whole span. Under this strategy, the loss above 90% span was suppressed by 48.17% and the loss of the whole span decreased 9.27%, which proved the PEW optimization design method with the strategy of local loss as the objective function is potential.
8 December 2020 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
The flow in a multistage axial compressor is highly unsteady, three-dimensional and turbulent. The interaction between compressor blade rows results in rotor/stator wake unsteadiness, which is not typically considered in the computational fluid dynamics (CFD) models. To gain depth and insight into the inner flow mechanism in multistage compressors, specifically the wake variability driven by the rotor/stator and stator/stator interactions, a compound total-pressure pneumatic probe with both high and low response-frequency were designed and manufactured. Unsteady rotor and stator wake measurements between blade rows for the third stage were carried out with this probe installing on a 3-DOF displacement mechanism, to deepen the knowledge of unsteady interactions in the embedded stages of a four-stage low-speed axial compressor. By performing frequency spectrum analysis and ensemble-average methods, higher spectral magnitude of the blade passing frequency (fBPF) and higher root mean square values of total pressure (PtRMS) at both sides of the stator wake region caused by the shedding of upstream boundary layer are revealed. In addition, the high-order harmonics are strengthened by the stator/stator interactions, especially near the blade tip. The individual contributions of rotor geometry variations/interactions of the upstream rotor wakes and the effects of downstream stator potential modulation to the wake variations can be understood.