Chenkai Zhang

Dr. Chenkai Zhang

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2017 in Aerospace Science and Technology
Verified
Journal Article
Closed access
CZChenkai Zhang
Chenkai Zhang
JHJun Hu
Jun Hu
JLJun Li
Jun Li
ZWZhiqiang Wang
Zhiqiang Wang

15 July 2014 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
CZChenkai Zhang
Chenkai Zhang
JHJun Hu
Jun Hu
ZWZhiqiang Wang
Zhiqiang Wang
To clearly clarify the effects of different upstream boundary layer thickness and tip clearance size to the detailed tip flow field and flow mechanism, numerical simulations are performed on a subsonic compressor rotor, which is used for low-speed model testing of a rear stage embedded in a modern high-pressure compressor. First, available experimental data are adopted to validate the numerical method. Second, comparisons are made for tip leakage vortex (TLV) structure, the interface of leakage flow/mainflow, endwall loss, isentropic efficiency and pressure-rise among different operating conditions. Then, effects of different clearance sizes and inflow boundary layer thicknesses are investigated. Finally, the self-induced unsteadiness at one near-stall (NS) operating condition is studied for different cases. Results show that the increment of tip clearance size has a deleterious effect on rotor efficiency and pressure-rise performance over the whole operating range, while thickening the inflow boundary layer is almost the same except that its pressure-rise performance will be increased at mass flow rate larger than design operating condition. Self-induced unsteadiness occurs at NS operating conditions, and its appearance largely depends on tip clearance size, while the effect of upstream boundary layer thickness is little.

28 May 2014 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
CZChenkai Zhang
Chenkai Zhang
ZWZhiqiang Wang
Zhiqiang Wang
CYChao Yin
Chao Yin
WYWei Yan
Wei Yan
JHJun Hu
Jun Hu
This paper discusses detailed experimental studies of a low-speed large-scale axial compressor, which is typical of an exit stage of HPC. Numerous measuring techniques were performed, and detailed experimental results were obtained, including inlet boundary layer total pressure distributions, overall compressor and model-stage performance, traverse flow field between blade rows and inside the stator for the model stage, static pressure on the stator blade and casing dynamic pressure of the rotor. The objective of the study is to assess the low-speed model compressor design and verify 3D computational fluid dynamics (CFD) code. Results show that inlet endwall blockage requirement of HPC exit stage is achieved; the low-speed model compressor design is fundamentally successful; the flow rate and pressure rise requirements are met at the design operating point, although the flow loss is relatively larger than design values for the lower half span, which can be attributed to a certain hub-corner separation. Furthermore, the reliability of adopted 3D commercial CFD code is validated. It is proved that the low-speed model testing technique is still a prospective way for the design of high performance HPC.

25 April 2020 in Energies
Verified
Journal Article
Open access
PDF file
JLJun Li
Jun Li
JHJun Hu
Jun Hu
CZChenkai Zhang
Chenkai Zhang
In order to investigate the flow structure and unsteady behavior of three-dimensional corner separation, a delayed detached-eddy simulation (DDES) method based on the Spalart–Allmaras (SA) model is performed on the third-stage stator of a multistage low-speed axial compressor. The stator simulation is validated by experiments before flow mechanism analysis. The complicated flow fields in the stator are then described step by step. Firstly, the structure and development process of vortices in corner separation flow are analyzed. Secondly, the velocity histogram of the monitor points in the mainstream and corner separation regions is obtained, and the velocity distribution of the corner separation region is discussed. Finally, Reynolds stress, Lumley anisotropy, turbulence energy spectra, and helicity density are discussed to understand the turbulence behavior of the corner separation flow in the stator. The results show that the corner separation appears at even the design condition and different kinds of vortical structures appear in the stator hub corner. The unsteadiness of corner separation flow is mainly reflected in the separation on the suction side of the blade and the wake shedding. Turbulence anisotropy and energy backscatter are found to be dominant in the separation region, which is correlated to the high shear stress.

27 July 2016 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
CZChenkai Zhang
Chenkai Zhang
JHJun Hu
Jun Hu
ZWZhiqiang Wang
Zhiqiang Wang
JLJun Li
Jun Li
Low-speed model testing (LSMT) plays a key role in advanced multistage high-pressure compressor (HPC) design recently, due to this, employing low-speed large-scale compressor to conduct 3D blading design and detailed flow mechanism investigation is convenient and cost-saving. This paper is one portion of a whole LSMT project for the seventh stage of an advanced commercial HPC, and experimental investigations of 3D blading optimizations for LSMT were presented in this paper, consisting of overall performances for the compressor and stage 3 and detailed flowfield measurements including area traverse for rotor 3 inlet, stator 3 inlet and outlet, area traverse inside stator 3 passage, and static pressure on stator 3 blade surface. Compared with the datum compressor, revised rotor 3 is J-type and hub restaggered, and the improved stator 3 possesses characteristics of controlled camber angle, reduced leading blade angle, forward movement of maximum thickness position, and larger bowed-shape. Experimental results show that efficiency is improved by 1%, and total pressure rise for the compressor and the third stage is raised by 1.4% and 10%, respectively, while the stalling mass flow rate is maintained. The effectiveness of improved design methods is confirmed, and it is a guide for further blading design and optimization, furthermore, detailed flowfield measurements reveal the basic flow mechanism of all the improvement methods. Moreover, the results indicate that utilization of cfd code in the optimization procedure is promising, and the reliability and feasibility of cfd code are verified with the detailed experimental results.

1 November 2010
Verified
Conference Paper
Closed access
CZChenkai Zhang
Chenkai Zhang
JHJun Hu
Jun Hu
It's vitally important for wind turbine aerodynamic performance predictions to design and optimize wind turbines. In view of the BEM method's fast speed and widespread use, this paper applies WT_Perf software of NREL to predict the performance on a NREL Phase VI upwind wind turbine. Measurements from the Phase VI of the NREL/NASA Ames wind tunnel test were used for validating the predictions. Performance predictions will vary greatly when data selection changes. Also three-dimensional rotational stall delay should be accounted for in the predictions. The final obtained prediction methods show good agreement with the experiments. Because of their accuracy and straightforward manufacturing, derived methods can be widely used in wind turbine optimization and design of the future research.