High-gain DC/DC converters are considered one of the most important components of green energy systems. Large numbers of these converters are used for increasing the voltage gain by using an extreme duty cycle. However, it increases losses and the cost, degrades the system performance, and hence obtains a low efficiency. In this article, a new design of a high-gain DC/DC boost converter is proposed. This converter has the potential to be used in low input voltage applications that need a high voltage gain such as systems powered by solar photovoltaic panels and fuel cells. The new topology is characterized by its simplicity of operation, high voltage gain, better efficiency, continuity of the input current, reduced number of inductors and capacitors, and can be extended to get higher gains. The converter structure, principle of operation, and design consideration of inductors and capacitors are presented in detail. Derivation of power losses and efficiency is presented. A laboratory prototype is implemented, and various experimental tests are given. The achievement of the suggested design is confirmed and compared with other recent high-gain converters.
In this paper, a new design of a non-isolated high-voltage gain DC/DC converter that operates at a reasonable duty cycle, by merging the dual boost converter with the switched inductor structure, is presented as a solution for the high-conversion ratio requirement. The proposed converter operates in discontinuous-current mode (DCM) with zero current switching for all switches and diodes. Wide duty cycle range operation, high output voltage gain, low switching stress, small switching losses, and high efficiency are achieved efficiently. Operating the converter in DCM can support a wide range of the duty cycle operation, maintain lower voltage stress of all devices, ensure the same current sharing among inductors, make it easy to control, provide more stability, and require a smaller inductor which reduces size and weight of the proposed converter. Moreover, the converter operates with a continuous input current. These features make the converter a good choice for many applications such as photovoltaic, x-ray, fuel cells, etc. To prove the converter’s effectiveness, theoretical analysis, project specifications, and operation principles are presented and studied. Experimental results in an open and closed-loop, and a comparison with other recent converters are also introduced to confirm the validity of the proposed converter.
14 September 2019 in Electric Power Components and Systems
In this article, different matrix converter (MC) control strategies are comprehensively explained. Further, an ultra-modified space vector modulation (UMSVM) of the MC is proposed. The total harmonic distortion for both output voltage and current is reduced, when the proposed UMSVM technique is applied. Moreover, a modified indirect space vector modulation with feed forward controller (MISVMFC) of the MC is also proposed in order to obtain a fixed output voltage and frequency for different wind speeds. The advantages of the MC are introduced in this article. These advantages include the wide range of the output frequency of MC, which may be greater than the input frequency and the control of both the output voltage magnitude and input displacement factor (IDF). Extensive theoretical and simulation results about conventional and proposed control techniques for the MC are presented. Experimental test bench is constructed and several experimental results are obtained. The experimental results validate the simulation ones.
This paper presents the closed-loop control of a single-switch high-gain multicell boost DC-DC converter working in a continuous conduction mode (CCM). This converter is particularly designed for applications in photovoltaic systems. One of the main advantages of the proposed converter is that it only employs one active semiconductor switch, which decreases the converter losses and cost, increases the efficiency, and simplifies the control circuit. Moreover, the multicell nature of the proposed converter offers the possibility of obtaining the required voltage gain by selecting the number of cells. State space average (SSA) modeling and small-signal analysis are used to model the switching converter power stages of the proposed converter. The parasitic series resistances of the passive elements of the converter circuit are considered to improve the accuracy of the modeling. Small-signal analysis is used to derive the open-loop transfer functions, input-to-output and control-to-output transfer functions of the proposed converter to examine its dynamic performance. The stability of the converter is analyzed to design the parameters of the voltage controller using the proposed modeling method. The experimental prototype of the proposed single-switch two-cell boost DC-DC converter was implemented. The simulation and experimental results proved the effectiveness of the proposed boost DC-DC converter under different working conditions. It has a fast dynamic response without overshoots. A comprehensive comparison between the proposed converter and previous boost converters is provided. It guarantees a required variable and constant high voltage gain with a wider duty ratio range. It compromises between the required performance, the low number of components, low voltage stress on the components, and cost-effectiveness. The experimental efficiency of the proposed converter is about 96% at a 100 W load.
Inverter-based systems encounter significant challenges in mitigating common-mode voltage (CMV) and minimizing inverter losses. Despite various space vector pulse-width modulation (SVPWM) techniques proposed to address these issues, a comprehensive comparative analysis has been lacking. This paper addresses this gap through an experimental and simulation-based evaluation of nine SVPWM techniques. A new discontinuous SVPWM technique, DSVPWM-K4, is introduced, which involves reversing the use of the two zero vectors in DSVPWM-K3. DSVPWM-K3 delivers superior performance in terms of CMV reduction, total harmonic distortion (THD), and inverter losses across all modulation indices (MI = 1, 0.75, 0.5, and 0.25), making it the most effective overall. Although DSVPWM-K4 is a novel approach, it ranks second in effectiveness. The RSPWM technique achieves the lowest CMV with a zero peak-to-peak value but is most effective at lower modulation indices (0.25 and 0.5) due to higher harmonic distortion at higher modulation indices. AZSPWM performs optimally at higher modulation indices, providing a 66.66% reduction in CMV compared to continuous SVPWM and significantly lower THD compared to RSPWM. In contrast, NSPWM exhibits nearly double the THD compared to continuous SVPWM.