The in-wheel motor (IWM) powertrain layout offers greater design flexibility and higher efficiency of an electric vehicle but has limited commercial success mainly due to the concerns of increased unsprung mass. This paper proposes a semi-active suspension system for in-wheel motors that combines both a dynamic vibration-absorbing structure (DVAS) and a PID-controlled MR damper, in order to achieve optimised comfort, handling and IWM vibration for a small car application. Whilst PID control and DVAS are not entirely new concepts, the usage of both optimisation techniques in a semi-active in-wheel motor suspension has seen limited implementation, which makes the current work novel and significant. The semi-active suspension operating both in passive fail-safe mode and full feedback control was compared to a conventional in-wheel motor passive suspension in terms of sprung mass acceleration, displacement, stator acceleration, tyre deflection and suspension travel for three different road profile inputs using MATLAB/Simulink. The implementation of a PID-controlled MR damper improved road comfort and road holding performance and decreased in-wheel motor vibration over the DVAS passive suspension mainly in terms of a maximum peak amplitude decrease of 40%, 35% and 32% for the sprung mass acceleration, tyre deflection and stator acceleration, respectively. The results are significant since they show that the use of a simple, easily implemented control scheme like PID control was able to significantly improve IWM suspension performance when paired with a DVAS. This study provides further confidence to manufacturers to commercially develop and implement the IWM layout as its major disadvantage can be reasonably addressed using a simple readily available control approach.
In this paper, a semi-active and fully active suspension system using a PID controller were designed and tuned in MATLAB/Simulink to achieve simultaneous optimisation of comfort and road holding ability. This was performed in order to quantify and observe the trends of both the semi-active and active suspension, which can then influence the choice of controlled suspension systems used for different applications. The response of the controlled suspensions was compared to a traditional passive setup in terms of the sprung mass displacement and acceleration, tyre deflection, and suspension working space for three different road profile inputs. It was found that across all road profiles, the usage of a semi-active or fully active suspension system offered notable improvements over a passive suspension in terms of comfort and road-holding ability. Specifically, the rms sprung mass displacement was reduced by a maximum of 44% and 56% over the passive suspension when using the semi-active and fully active suspension, respectively. Notably, in terms of sprung mass acceleration, the semi-active suspension offered better performance with a 65% reduction in the passive rms sprung mass acceleration compared to a 40% reduction for the fully active suspension. The tyre deflection of the passive suspension was also reduced by a maximum of 6% when using either the semi-active or fully active suspension. Furthermore, both the semi-active and fully active suspensions increased the suspension working space by 17% and 9%, respectively, over the passive suspension system, which represents a decreased level of performance. In summary, the choice between a semi-active or fully active suspension should be carefully considered based on the level of ride comfort and handling performance that is needed and the suspension working space that is available in the particular application. However, the results of this paper show that the performance gap between the semi-active and fully active suspension is quite small, and the semi-active suspension is mostly able to match and sometimes outperform the fully active suspension n in certain metrics. When considering other factors, such as weight, power requirements, and complexity, the semi-active suspension represents a better choice over the fully active suspension, in the author’s opinion. As such, future work will look at utilising more robust control methods and tuning procedures that may further improve the performance of the semi-active suspension.
This research focuses on addressing a significant concern in the aviation industry, which is drag. The primary objective of this project is to achieve drag reduction through the implementation of riblets on a wing featuring the NACA 2412 aerofoil, operating at subsonic speeds. Riblets, with the flow direction on wing surfaces, have demonstrated the potential to effectively decrease drag in diverse applications. This investigation includes computational analysis within the ANSYS Workbench framework, employing a polyhedral mesh model. The scope of this research encompasses the analysis of both a conventional wing and a modified wing with riblets. A comparative analysis is conducted to assess variations in drag values between the two configurations. Parameters, including geometry, dimensions, and riblet placement at varying angles of attack, are explored to comprehend their impact on drag reduction. Notably, 15.6% and 23% reductions in drag were identified at a 16-degree angle of attack with midspan and three-riblet models, separately. The computational mesh and method were validated using appropriate techniques.
The proliferation of electronic loads has led to a substantial increase in harmonic emissions within low-voltage distribution networks. The accurate estimation of the expected levels of harmonics in a network is a daunting task for network operators. Stochastic-based harmonic estimation models can offer a comprehensive assessment of the expected levels of harmonics in the presence of existing and future loads, including electric vehicles and smart-grid-enabled devices. Such models offer a valuable tool for network operators to assess the potential impact of harmonics on future networks and to create sustainable design solutions to meet the increasing demand for electricity while achieving net zero targets. However, several variables associated with these estimations models involve a level of uncertainty due to their stochastic nature, leading to inaccuracies in the estimations. This paper aims to provide a more realistic estimate of these uncertainties in order to improve the outcomes of harmonic estimation models for the development of sustainable distribution networks.
Additive manufacturing (AM) has greatly revolutionized manufacturing due to its ability to manufacture complex shapes without the need for additional tooling. Most AM applications are based on geometries comprising curved shapes subjected to impact loads. The main focus of this study was on investigating the influence of infill density and the radius of curvature on the impact strength of parts manufactured via an FDM process. Standard geometrical specimens with varying part infill densities and radii of curvature were produced and subjected to Charpy impact tests to evaluate their impact strength. The results suggest that the impact strength increases with the increased density caused by higher amounts of material as well as by the changing cross-sectional areas of the beads. Also, the radius of curvature of the parts shows a clear inverse relationship with the impact energy absorbed by the specimens (i.e., increasing the radius decreased the impact energy of the parts) produced via an FDM process, which can be explained using the beam theory of structural mechanics. The maximum value of impact strength obtained was 287 KJ/m2, and this was achieved at the highest infill density (i.e., solid) and for the smallest radius of curvature.
Three-piece alloy wheels are widely used across the automotive industry, favoured due to their lightweight construction and ease of customisation. Vehicle wheels must withstand forces generated during acceleration, braking, cornering, and impacts, ensuring safety and durability under real-world conditions. Finite element analysis (FEA) plays a crucial role in simulating these loading conditions, thoroughly assessing structural performance prior to manufacturing. This study develops and validates a digital FEA testing framework tailored to low-volume wheel manufacturers, demonstrating that FEA can replace traditional physical wheel fatigue tests where such facilities are unavailable. This research was conducted in collaboration with a UK company specialising in the design and manufacture of bespoke, limited-production three-piece alloy wheels. However, the absence of dedicated structural testing procedures caused many of their existing designs to be overengineered, resulting in excessive material usage, increased weight, and high production costs. In some cases, lack of testing also contributed to wheel failures. This work selected three of the company’s existing wheel designs and subjected them to comprehensive analysis. Using FEA, each wheel was evaluated under industry-standard radial, cornering, biaxial, and impact tests. To verify the simulations, a known case of wheel failure was analysed and compared to real-world values. Once verified, any design issues were addressed. The redesigned wheels achieved substantial weight reduction (up to 25%), while still meeting or exceeding the relevant safety standards and allowing for manufacturability. Ultimately, this work demonstrated that applying digital simulation techniques can significantly improve the performance and safety of custom three-piece alloy wheels.