Abdunnaser Hamza Fadel

Dr. Abdunnaser Hamza Fadel

Department of Materials and Metallurgical Engineering, University of Zawia, Az Zāwīyah, Az Zāwiyah, Libya
orcid
Associate Professor - University of Zawia - Faculty of Oil,...

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2012 in Journal of Materials Science & Technology
Verified
Journal Article
Closed access
Abdunnaser Hamza FadelAbdunnaser Hamza Fadel
Abdunnaser Hamza Fadel
DGDragomir Gliŝić
Dragomir Gliŝić
NRNenad Radović
Nenad Radović
DDDjordje Drobnjak
Djordje Drobnjak

1 January 2010 in ISIJ International
Verified
Journal Article
Closed access
DGDragomir Glišić
Dragomir Glišić
NRNenad Radović
Nenad Radović
AKAnkica Koprivica
Ankica Koprivica
Abdunnaser Hamza FadelAbdunnaser Hamza Fadel
Abdunnaser Hamza Fadel
DDDjordje Drobnjak
Djordje Drobnjak

1 January 2013 in Journal of Mining and Metallurgy, Section B: Metallurgy
Verified
Journal Article
Open access
Abdunnaser Hamza FadelAbdunnaser Hamza Fadel
Abdunnaser Hamza Fadel
DGD. Glisic
D. Glisic
NRNenad Radović
Nenad Radović
DDD. Drobnjak
D. Drobnjak
The aim of this work was to determine TTT diagram of medium carbon V-N micro-alloyed steel with emphasis on the development of intragranular ferrite morphologies. The isothermal treatment was carried out at 350, 400, 450, 500, 550 and 600?C. These treatments were interrupted at different times in order to analyze the evolution of the microstructure. Metallographic evaluation was done using optical and scanning electron microscopy (SEM). The results show that at high temperatures (? 500?C) polygonal intragranulary nucleated ferrite idiomorphs, combined with grain boundary ferrite and pearlite were produced and followed by an incomplete transformation phenomenon. At intermediate temperatures (450, 500?C) an interloced acicular ferrite (AF) microstructure is produced, and at low temperatures (400, 350?C) the sheave of parallel acicular ferrite plates, similar to bainitic sheaves but intragranularly nucleated were observed. In addition to sheaf type acicular ferrite, the grain boundary nucleated bainitic sheaves are observed.

24 June 2021 in Metals
Verified
Journal Article
Open access
PDF file
SDStefan Dikić
Stefan Dikić
Dragomir GlišićDragomir Glišić
Dragomir Glišić
Abdunnaser Hamza FadelAbdunnaser Hamza Fadel
Abdunnaser Hamza Fadel
GJGvozden Jovanović
Gvozden Jovanović
NRNenad Radović
Nenad Radović
Isothermal transformation characteristics of a medium carbon Ti-V microalloyed steel were investigated using light microscopy, scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS), and by uniaxial compressive testing. Samples austenitized on 1100 °C were isothermally treated in the range from 350 to 600 °C and subsequently water quenched. The final microstructure of the samples held at 350 °C consisted of bainitic sheaves and had compressive yield strength, approximately from 1000 MPa, which is attributed to high dislocation density of low bainite. At 400 and 450 °C, acicular ferrite became prevalent in the microstructure. It was also formed by a displacive mechanism, but the dislocation density was lower, leading to a decrease of compressive yield strength to approximately 700 MPa. The microstructure after the heat treatment at 500 °C consisted of coarse non-polygonal ferrite grains separated by pearlite colonies, principally dislocation free grains, so that the compressive YS reached a minimum value of about 700 MPa. The microstructure of the samples heat-treated at 550 and 600 °C consisted of pearlite and both grain boundary and intragranular ferrite, alongside with some martensite. After 600 s, austenite became stable and transformed to martensite after water quenching. Therefore, the presence of martensite increased the compressive YS to approx. 800 MPa.

1 January 2013
Verified
Journal Article
Open access
DGDragomir Glisic
Dragomir Glisic
Abdunnaser Hamza FadelAbdunnaser Hamza Fadel
Abdunnaser Hamza Fadel
NRNenad Radovic
Nenad Radovic
DDDjordje Drobnjak
Djordje Drobnjak
MZMilorad Zrilic
Milorad Zrilic
The aim of this work was to establish deformation behaviour of two vanadium microalloyed medium carbon steels with different contents of carbon and titanium by tensile testing at 77 K. Samples were reheated at 1250?C/30 min and continuously cooled at still air. Beside acicular ferrite as dominant morphology in both microstructures, the steel with lower content of carbon and negligible amount of titanium contains considerable fraction of grain boundary ferrite and pearlite. It was found that Ti-free steel exhibits higher strain hardening rate and significantly lower elongation at 77 K than the fully acicular ferrite steel. The difference in tensile behavior at 77 K of the two steels has been associated with the influence of the pearlite, together with higher dislocation density of acicular ferrite.

1 January 2014 in Procedia Materials Science
Verified
Journal Article
Open access
DGDragomir Glišić
Dragomir Glišić
NRNenad Radović
Nenad Radović
DDDjordje Drobnjak
Djordje Drobnjak
Abdunnaser Hamza FadelAbdunnaser Hamza Fadel
Abdunnaser Hamza Fadel
Cleavage fracture of the medium carbon V-microalloyed steel with structure consisting of acicular ferrite, pearlite and grain boundary ferrite has been investigated by means of four-point bending of the notched samples at -196°C. It was found that cleavage fracture initiation has not been related to the coarse second phase particles cracking. Calculated values of the effective surface energy of 49J/m2 and critical cleavage fracture stress normalized by yield stress of 1.84 are in agreement with the results for the steels with ferrite-pearlite and bainite structures