This paper presents the design and construction of a hydroponics monitoring system that can collect parameters of hydroponic systems, such as temperature, water limit, pH level, and nutrient levels. The monitoring system was developed using an ESP32 microcontroller and several sensors, including total dissolved solids (TDS), pH, water level, and temperature sensors. The ESP32 microcontroller gathers and processes data from the sensors to automatically activate the water or salt pump and drain the necessary materials into the hydroponic system's plant basin. The user can then view the hydroponic parameters through the Blynk application on a smartphone. The user can also activate the pumps for water, nutrients, or salt using the application's interface on a smartphone, or the ESP32 microcontroller can activate them automatically if the parameter values deviate from the required values. The monitoring hydroponics system and IoT interface were successfully built and implemented. The experiments were compiled, and the data gathered and discussed. • An ESP32 microcontroller with TDS, pH, water level, and temperature sensors was used to build the hydroponic monitoring system. • The ESP32 automatically collects and evaluates sensor data in order to drain water nutrients, or salt into the plant basin of the hydroponic system as necessary. • The user can also check the parameters of the hydroponic system and, if necessary, run the pumps for water, fertilizers, or salt using his smartphone through the Blynk IoT app.
1 March 2019 in International Journal of Power Electronics and Drive Systems (IJPEDS)
The CO2 emission level is becoming a serious issue worldwide. The continuous increase in gasoline price forms the essential base of development of electric vehicle (EV) drives. Moreover, economic and environmental issues relate to fabrication and operation of traditional powered vehicles. The basic considerations and development perspectives of EVs are presented in this paper. The development of an efficiently designed motor and drive satisfy the need of efficient characteristics that enable EVs to perform as part of the propulsion unit. The use of digital signal controllers compared with conventional control systems minimizes the motor’s total harmonic distortion, lowers operating temperatures, and produces high efficiency and power factor ratings. This paper addresses the view of EV technology as well its advantages over other technologies.
This paper presents the design and implementation of a closed-loop solar tracker system. The demand for clean energy sources has increased along with the rising demand for electrical energy and the increasing amount of environment pollution triggered by fuel consumption. Among these sources, solar energy is considered the most feasible given its wide availability and easy operation in different environments. The main purpose of this study is to maximize the generated photovoltaic power and reduce CO2 emissions by designing an efficient and low-cost solar tracking system. An aligned closed-loop solar tracker is designed and constructed to achieve the best accuracy. The proposed system shows more freedom in its movement to overcome the problems associated with the tilt of the frame-holder. A PIC microcontroller based on the Flowcode programming language is used, the position feedback is detected by using a photo-sensor, and the H-Bridge driver is used to control two DC motors. According to the experimental results, the proposed system shows significant improvements in efficiency compared with stationary solar tracking systems.
In this paper, a novel flying-capacitor-half-bridge 5-level inverter is studied which is composed of a half-bridge capacitor-clamp inverter and a conventional half-bridge inverter connected to a common split-capacitor power supply. Analysis of a modulation technique for the inverter, which incorporates square-wave synthesis in conjunction with the PWM subharmonic method, is illustrated. According to the proposed control technique, new configuration permits faster devices and higher voltage devices operating together. In order to estimate spectra accurately, the mathematic models of the modulation process with three carrier dispositions will be built, at the same time rigorous analytic solution of spectra is derived from an extension of Bennet's method. We illustrate and sum up spectral feature of output waveform covering all operation conditions. In order to verify the proposed approach simulation validation is carried out.
1 March 2025 in Journal of Robotics and Control (JRC)
Improving the quality of the produced artwork would require the development of computer numerical control (CNC) technology for various wood shaping processes. This paper presents the development and implementation of a CNC wood carving machine. This project aims to produce wood carvings with high precision and low cost. The electronic components were selected, the mechanical frame of the machine was built, and all parts of the machine were assembled and installed. The presented wood carving machine is based on the principle of drawing the desired shape, translating it into G-code, and then sending it to the microcontroller program. The microcontroller sends instructions to the CNC shield, which drives three stepper motors in a synchronized manner in order to produce the desired carving model. The maximum workpiece of the caving machine designed to be 30x30 cm. Experiments were conducted to test the functionality of the proposed CNC wood carving machine. The results showed that the carved models created by this machine had a carving precision range from ±0.1 to ±0.15 mm and a carving speed of approximately 500 rpm. The proposed CNC can be used to produce low-cost artisanal woodwork applications.