Ada Steponavičiūtė

Ms. Ada Steponavičiūtė

Center for Physical Sciences and Technology
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 November 2021 in Mathematics
Verified
Journal Article
Open access
PDF file
RPRomuald Petkevič
Romuald Petkevič
GJGiedrius Jočbalis
Giedrius Jočbalis
ASAda Steponavičiūtė
Ada Steponavičiūtė
KSKarolis Stravinskas
Karolis Stravinskas
ARAleksej Romanov
Aleksej Romanov
GMGenrik Mordas
Genrik Mordas
Metal additive manufacturing has received much attention in the past few decades, and it offers a variety of technologies for three-dimensional object production. One of such technologies, allowing large-sized object production, is laser-assisted metal deposition, the limits of which are determined by the capabilities of the positioning system. The already-existing nozzles have either a relatively low build rate or a poor resolution. The goal of this work is to develop a new nozzle with a centered particle beam at high velocity for the laser-assisted metal additive manufacturing technologies. Scientific challenges are addressed with regards to the fluid dynamics, the particle-substrate contact, and tracking of the thermodynamic state during contact. In this paper, two nozzles based on the de Laval geometry with Witoszynski and Bicubic curves of convergence zone were designed; the results showed that the average flow velocity in a Bicubic outlet curve nozzle is around 615 m/s and in Witoszynski this is 435 m/s. Investigation of particle beam formation for the Bicubic curve geometry revealed that small particles have the highest velocity and the lowest total force at the nozzle outlet. Fine particles have a shorter response time, and therefore, a smaller dispersion area. The elasto-plastic particle-surface contact showed that particles of diameter limited up to 3 μm are able to reach experimentally obtained critical velocity without additional heating. For particle sizes above 10 μm, additional heating is needed for deposition. The maximum coefficient of restitution (COR) is achieved with a particle size of 30 μm; smaller particles are characterized by the values of COR, which are lower due to a relatively high velocity. Particles larger than 30 μm are scalable, characterized by a small change in velocity and a rise in temperature as their mass increases.

1 January 2022 in Materials Today: Proceedings
Verified
Journal Article
Closed access
ASAda Steponavičiūtė
Ada Steponavičiūtė
ASAušra Selskienė
Aušra Selskienė
KSKarolis Stravinskas
Karolis Stravinskas
SBSergejus Borodinas
Sergejus Borodinas
GMGenrik Mordas
Genrik Mordas

30 October 2024 in Mechanics
Verified
Journal Article
Open access
PDF file
َSَAlireza Shahidi
َAlireza Shahidi
KSKarolis Stravinskas
Karolis Stravinskas
ASAda Steponavičiūtė
Ada Steponavičiūtė
AKArtūras Kilikevičius
Artūras Kilikevičius
DVDarius Vainorius
Darius Vainorius
GMGenrik Mordas
Genrik Mordas
This study investigates the mechanical properties of ceramic and photopolymer composites created using stereolithography (SLA) 3D printing. It aims to evaluate and compare the performance of two SLA materials: Liqcreate Composite-X and Phrozen's Water-Washable Resin, using dynamic flexural vibration tests to determine Young's modulus. Liqcreate Composite-X, a photopolymer resin with excellent mechanical properties, including high tensile and flexural strength, showed a first resonance frequency of 318 Hz and a Young's modulus of 0.93 x 1010 Pa. Phrozen's Water-Washable Resin, designed for easy post-processing, had a first resonance frequency of 210 Hz and a Young's modulus of 0.30 x 1010 Pa. In conclusion, Liqcreate Composite-X demonstrates superior mechanical performance, making it suitable for high-strength applications, while Phrozen's Water-Washable Resin, with lower mechanical properties, is more suited for less demanding uses. This study enhances the understanding and application of SLA-based ceramic composites in various engineering domains.