This study presents a comparative evaluation of injection-moulded PA12 composites reinforced with AlSi10Mg and 304 SS fillers, with emphasis on microstructure–property correlations linking powder morphology, mechanical performance, thermal stability, and tribological behaviour. Powder characterization revealed distinct morphologies—fine spherical AlSi10Mg particles (D50 ≈ 32 µm) dispersed uniformly in the matrix—while SS particles (D50 ≈ 245 µm) tended to agglomerate, leading to interfacial voids. Tensile testing showed that the elastic modulus of neat PA12 (0.95 GPa) increased by 20% and 28% with 20 wt% AlSi10Mg and SS, respectively. However, tensile strength decreased from 35.04 MPa (PA12) to 32.18 MPa (20 wt% AlSi10Mg) and 31.03 MPa (20 wt% 304 SS), consistent with stress concentrations around particle clusters. Hardness values remained nearly unchanged at 96–98 Shore D across all composites. Thermal analysis indicated that AlSi10Mg promoted crystallization, increasing crystallinity from 31% (PA12) to 34% and raising Tm by 2 °C. In contrast, 304 SS reduced crystallinity to 28% but significantly improved thermal stability, shifting Tonset from 405 °C (PA12) to 426 °C at 20 wt%. Tribological tests demonstrated substantial improvements: the coefficient of friction decreased from 0.42 (PA12) to 0.34 (AlSi10Mg) and 0.29 (304 SS), while wear rates dropped by 40% and 55%, respectively. SEM confirmed smoother worn surfaces in AlSi10Mg composites and abrasive grooves in 304 SS composites. The findings show that AlSi10Mg is advantageous for smoother surfaces and improved crystallinity, while SS enhances stiffness, wear resistance, and thermal endurance, providing design guidelines for PA12 composites in aerospace, automotive, and engineering applications.
Metal additive manufacturing has received much attention in the past few decades, and it offers a variety of technologies for three-dimensional object production. One of such technologies, allowing large-sized object production, is laser-assisted metal deposition, the limits of which are determined by the capabilities of the positioning system. The already-existing nozzles have either a relatively low build rate or a poor resolution. The goal of this work is to develop a new nozzle with a centered particle beam at high velocity for the laser-assisted metal additive manufacturing technologies. Scientific challenges are addressed with regards to the fluid dynamics, the particle-substrate contact, and tracking of the thermodynamic state during contact. In this paper, two nozzles based on the de Laval geometry with Witoszynski and Bicubic curves of convergence zone were designed; the results showed that the average flow velocity in a Bicubic outlet curve nozzle is around 615 m/s and in Witoszynski this is 435 m/s. Investigation of particle beam formation for the Bicubic curve geometry revealed that small particles have the highest velocity and the lowest total force at the nozzle outlet. Fine particles have a shorter response time, and therefore, a smaller dispersion area. The elasto-plastic particle-surface contact showed that particles of diameter limited up to 3 μm are able to reach experimentally obtained critical velocity without additional heating. For particle sizes above 10 μm, additional heating is needed for deposition. The maximum coefficient of restitution (COR) is achieved with a particle size of 30 μm; smaller particles are characterized by the values of COR, which are lower due to a relatively high velocity. Particles larger than 30 μm are scalable, characterized by a small change in velocity and a rise in temperature as their mass increases.
This study introduces a novel ceramic-composite resin specifically developed for stereolithography (SLA) 3D printing, aimed at enhancing dental restorations. The integration of advanced digital technologies in dentistry has shifted traditional methods towards more precise and efficient techniques such as computer-aided design/computer-aided manufacturing (CAD/CAM). However, these processes typically involve material waste due to their subtractive nature. Additive manufacturing, or 3D printing, particularly SLA, which uses ultraviolet light to cure photosensitive resins, presents a viable alternative with the potential for creating detailed, custom restorations with minimal waste. Our research focuses on formulating and evaluating a ceramic-composite resin that combines the benefits of light-cured materials with the mechanical robustness required for dental applications. We conducted comprehensive tests to assess the printability, mechanical properties and wear resistance of the developed material. The ceramic-composite resin demonstrated a tensile strength of approximately 73 MPa, significantly higher than the 42 MPa observed for traditional photopolymer resins. Additionally, the ceramic-composite resin showed ability to resist incidental friction and wear. This research could significantly impact the dental prosthetics field by providing a method for producing high-performance, patient-specific restorations efficiently and cost-effectively.
This study investigates the mechanical properties of ceramic and photopolymer composites created using stereolithography (SLA) 3D printing. It aims to evaluate and compare the performance of two SLA materials: Liqcreate Composite-X and Phrozen's Water-Washable Resin, using dynamic flexural vibration tests to determine Young's modulus. Liqcreate Composite-X, a photopolymer resin with excellent mechanical properties, including high tensile and flexural strength, showed a first resonance frequency of 318 Hz and a Young's modulus of 0.93 x 1010 Pa. Phrozen's Water-Washable Resin, designed for easy post-processing, had a first resonance frequency of 210 Hz and a Young's modulus of 0.30 x 1010 Pa. In conclusion, Liqcreate Composite-X demonstrates superior mechanical performance, making it suitable for high-strength applications, while Phrozen's Water-Washable Resin, with lower mechanical properties, is more suited for less demanding uses. This study enhances the understanding and application of SLA-based ceramic composites in various engineering domains.