This paper analyzes control strategies for induction motors in railway applications. The paper will focus on drives operating with a low switching to fundamental frequency ratio and in the overmodulation region or six-step operation, as these are the most challenging cases. Modulation methods, efficient modes of operation of the drive and the implications for its dynamic performance, and machine design will also be discussed. Extensive simulation results, as well as experimental results, obtained from a railway traction drive, are provided.
Maximum power point tracking (MPPT) is a technique involved in photovoltaic (PV) systems for optimizing the output power of solar panels. Traditional solutions like perturb and observe (P&O) and Incremental Conductance (IC) are commonly utilized to follow the MPP under various environmental circumstances. However, these algorithms suffer from slow tracking speed and low dynamics under fast-changing environment conditions. To cope with these demerits, a data-driven artificial neural network (ANN) algorithm for MPPT is proposed in this paper. By leveraging the learning capabilities of the ANN, the PV operating point can be adapted to dynamic changes in solar irradiation and temperature. Consequently, it offers promising solutions for MPPT in fast-changing environments as well as overcoming the limitations of traditional MPPT techniques. In this paper, simulations verification and experimental validation of a proposed data-driven ANN-MPPT technique are presented. Additionally, the proposed technique is analyzed and compared to traditional MPPT methods. The numerical and experimental findings indicate that, of the examined MPPT methods, the proposed ANN-MPPT approach achieves the highest MPPT efficiency at 98.16% and the shortest tracking time of 1.3 s.
6 September 2023 in IEEE Transactions on Transportation Electrification
Modern railway traction systems are often equipped with anti-slip control strategies to comply with performance and safety requirements. A certain amount of slip is needed to increase the torque transferred by the traction motors onto the rail. Commonly, constant slip control is used to limit the slip velocity between the wheel and rail avoiding excessive slippage and vehicle derailment. This is at the price of not fully utilizing the train’s traction and braking capabilities. Finding the slip at which maximum traction force occurs is challenging due to the non-linear relationship between slip and wheel-rail adhesion coefficient, as well as to its dependence on rail and wheel conditions. Perturb and observe (P&O) and steepest gradient (SG) methods have been reported for the Maximum Adhesion Tracking (MAT) search. However, both methods exhibit weaknesses. Two new MAT strategies are proposed in this paper which overcome the limitations of existing methods, using Fuzzy Logic Controller (FLC) and Particle Swarm Optimization (PSO) respectively. Existing and proposed methods are first simulated and further validated experimentally using a scaled roller rig under identical conditions. The results show that the proposed methods improve the traction capability with lower searching time and oscillations compared to existing solutions. Tuning complexity and computational requirements will also be shown to be favorable to the proposed methods.
Torsional vibrations phenomena are self-excited vibrations that occur in the wheelset of railway powertrains due to the counter-phase oscillation of both wheels. Long-lasting events of this type may lead to the catastrophic failures. Therefore, torsional vibration suppression and mitigation methods have drawn significant attention from the railway industry in the recent few years. Conventional vibration suppression methods reduce motor torque once the oscillation is detected. However, this can result in trip delays. Design of methods which do not compromise the traction capability is challenging. This paper proposes a novel torsional vibration suppression method using a Proportional-Resonant (PR) controller. The proposed method is insensitive to mechanical drive-train parameter variation neither requires adding new sensors to the wheelset. The method requires previous knowledge of the natural frequency of the wheelset torsional mode but this significantly reduces the implementation complexity suffered by other anti-vibration methods. Furthermore, the method will be shown to provide reduced sensitivity to slip velocities and wheel-rail conditions.
5 December 2022 in IEEE Transactions on Vehicular Technology
Anti-slip control is a prominent part of modern railway traction control systems due both to performance and safety concerns. This paper explains the development of a scaled roller-rig test bench which emulates the rail and the wheel of a train. The final purpose of the developed roller-rig test bench is twofold: to study the theory/behaviour of existing anti-slip strategies and to test new designs, before their implementation in the real system. Estimation of adhesion coefficient using a disturbance observer method is explained and tested under various conditions. Anti-slip control is implemented in wheel drive using a direct method by adding a slip speed controller. The tests are conducted using both fixed roller speed and variable roller speed, i.e. dynamic roller. In this second case, train inertia emulation will be key. Two methods are proposed to emulate train inertia, being this the main contribution of this paper. Both methods are verified in simulation first, and further confirmed experimentally in the test bench.
This paper performs a comparative analysis of overmodulation methods for AC electric drives. Criteria for the analysis considers three aspects: output vs. commanded modulation index (i.e., linearity); harmonic content; and the number of commutations (i.e., switching losses). The analysis focuses on existing methods reported in the literature. Improvements for the existing methods will be proposed as a result of the analysis. The analysis is experimentally validated on a three-phase three-level Neutral-Point-Clamped (NPC) inverter.