Amaia Iturrioz Zabala

Mrs. Amaia Iturrioz Zabala

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 April 2018 in Welding in the World
Verified
Journal Article
Closed access
PDF file
AZAmaia Iturrioz Zabala
Amaia Iturrioz Zabala
EGE. Gil
E. Gil
MPM. M. Petite
M. M. Petite
FGF. Garciandia
F. Garciandia
AMA. M. Mancisidor
A. M. Mancisidor
MSMaria San Sebastian
Maria San Sebastian

23 March 2021 in Metals
Verified
Journal Article
Open access
PDF file
MAMaider Arana
Maider Arana
Eneko UkarEneko Ukar
Eneko Ukar
IRIker Rodriguez
Iker Rodriguez
AZAmaia Iturrioz Zabala
Amaia Iturrioz Zabala
PAPedro Alvarez
Pedro Alvarez
With the advent of disruptive additive manufacturing (AM), there is an increasing interest and demand of high mechanical property aluminium parts built directly by these technologies. This has led to the need for continuous improvement of AM technologies and processes to obtain the best properties in aluminium samples and develop new alloys. This study has demonstrated that porosity can be reduced below 0.035% in area in Al-Mg samples manufactured by CMT-based WAAM with commercial filler metal wires by selecting the correct shielding gas, gas flow rate, and deposition strategy (hatching or circling). Three phase Ar+O2+N2O mixtures (Stargold®) are favourable when the hatching deposition strategy is applied leading to wall thickness around 6 mm. The application of circling strategy (torch movement with overlapped circles along the welding direction) enables the even build-up of layers with slightly thicker thickness (8 mm). In this case, Ar shielding gas can effectively reduce porosity if proper flow is provided through the torch. Reduced gas flows (lower than 30 Lmin) enhance porosity, especially in long tracks (longer than 90 mm) due to local heat accumulation. Surprisingly, rather high porosity levels (up to 2.86 area %) obtained in the worst conditions, had a reduced impact on the static tensile test mechanical properties, and yield stress over 110 MPa, tensile strength over 270 MPa, and elongation larger than 27% were achieved either for Ar circling, Ar hatching, or Stargold® hatching building conditions. In all cases anisotropy was lower than 11%, and this was reduced to 9% for the most appropriate shielding conditions. Current results show that due to the selected layer height and deposition parameters there was a complete re-melting of the previous layer and a thermal treatment on the prior bottom layer that refined the grain size removing the original dendritic and elongated structure. Under these conditions, the minimum reported anisotropy levels can be achieved.

14 November 2023 in Metals
Verified
Journal Article
Open access
PDF file
LVLexuri Vázquez
Lexuri Vázquez
AZAmaia Iturrioz Zabala
Amaia Iturrioz Zabala
PUPablo Lopez de Uralde
Pablo Lopez de Uralde
PAPedro Alvarez
Pedro Alvarez
The CMT-Twin-based wire and arc additive manufacturing (WAAM) process for 5356 aluminium alloy has been investigated focusing on the optimisation of welding parameters to maximise the deposition rate while avoiding segregation-related problems during solidification. For that, different conditions have been studied regarding interpass dwell time and the use of forced cooling. The larger heat input produced by the double-wire CMT-Twin process, compared to the single-wire CMT, creates vast segregations for less intensive cooling conditions and short dwell times that can induce cracks and reduce ductility. Thermography has been applied to set a maximum local temperature between consecutive layers avoiding those segregations and pores, and to optimise the total manufacturing time by varying the interpass dwell time along the height of the wall. Only a constant interpass long dwell time of 240 s and the new optimised strategy were effective in avoiding merged segregations, reducing the latest total manufacturing time by 36%. Obtained tensile properties are comparable to other works using WAAM for this alloy, showing lower properties in the vertical orientation. The use of CMT-Twin-based welding technology together with variable interpass dwell time controlled by thermography is an interesting alternative to build up parts with wall thicknesses around of 10 mm in a reduced time.

6 December 2024 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
AZAmaia Iturrioz Zabala
Amaia Iturrioz Zabala
Eneko UkarEneko Ukar
Eneko Ukar
Juan Carlos Pereira FalconJuan Carlos Pereira Falcon
Juan Carlos Pereira Falcon
The influence of the manufacturing strategy of Invar 36 alloy parts manufactured by Directed Energy Deposition by Arc (DED-Arc) also known as wire and arc additive manufacturing (WAAM) using cold metal transfer (CMT) technology has been investigated. This study focuses on the influence of applying different deposition strategies on the resulting microstructure and mechanical properties. As manufacturing costs and time are critical issues which determine the business case in WAAM applications, it is important to use the smallest possible amount of feedstock material. Therefore, different manufacturing strategies are used to obtain the variable wall thicknesses required for each part preform using WAAM as a manufacturing route. Differences in manufacturing temperature and thermal history due to different deposition strategies have been recorded. Deep microstructural analysis in as-built condition revealed that granular alignment and the crystallographic texture obtained differ between deposition strategies studied. This is the reason why there are differences in the mechanical properties, such as yield strength, ultimate tensile strength, elongation, and hardness, of the different strategies analyzed. The results revealed that the higher strength is obtained in three overlapped weld beads for the walls (514 and 581 MPa in building direction and perpendicular direction, respectively), compared to single weld bead wall (481 and 489 MPa), circular single weld bead wall (460 and 484 MPa), and meandering weld bead wall (467 and 439 MPa). The opposite is true for elongation, which is a typical correlation between strength and ductility in Fe-based alloys, having the highest elongation in the meandering weld bead wall (26 and 30%) and circular single weld bead (30 and 27%) compared to single weld bead wall (27 and 23%) and three overlapped weld bead wall (23 and 20%). It can therefore be concluded that an Invar 36 alloy part manufactured by CMT-WAAM with different strategies will have different mechanical properties, having a difference in ultimate tensile strength of 54 MPa and 142 MPa, and in elongation of 7% and 10% in building direction and perpendicular direction, respectively, between the most and the least resistant zone.

12 November 2025 in Materials
Verified
Journal Article
Open access
PDF file
AZAmaia Iturrioz Zabala
Amaia Iturrioz Zabala
Juan Carlos Pereira FalconJuan Carlos Pereira Falcon
Juan Carlos Pereira Falcon
Eneko UkarEneko Ukar
Eneko Ukar
This research explored the technical feasibility of creating a controlled chemical composition for Fe-Ni alloys using a Directed Energy Deposition (DED) arc metal additive manufacturing (AM) process in its twin wire feed mode. This method employs two independently controlled arc power sources to feed two different wires into a single torch, creating a unified melt pool protected by a single shielding gas nozzle. The research focused on producing Invar 36 (EN 1.3912), a low thermal expansion alloy, by melting and mixing steel and Ni-Fe wires using Cold Metal Transfer-Twin (CMT-Twin) technology. This method enables the fabrication of multi-material components featuring regions with distinct chemical compositions, including functional gradients, with the aim of leveraging the advantageous properties of each individual material. Furthermore, this new manufacturing route offers the possibility to avoid using some alloying elements, such as Nb, an element considered a critical raw material (CRM) in the European Union (EU). Microstructure and mechanical properties were analyzed and compared to commercial Invar 36 obtained by DED-Arc with single wire as well as the effect of the absence of Nb. Results showed that the in situ obtained alloy had 10–20% lower strength but exhibited 10–15% higher elongation compared to the commercial alloy, making it a promising alternative for advanced manufacturing by using this new manufacturing route.