This research focused on the development of biomaterials based on cassava starch and corn starch and on the effect of the incorporation of polycaprolactone (PCL) on the thermal and thermomechanical properties of the blends. The results indicated partial compatibility in the blends, especially with cassava starch at a content of 20 wt% as reflected by the maintenance of tensile strength and elongation. In addition, the changes in the crystal quality of PCL and the displacement of the absorption bands of the carbonyl groups of PCL in the infrared (989–1000 cm−1), attributed to the formation of hydrogen bonds between these groups and the hydroxyl groups of starches, were also associated with compatibility. It was observed that the crystallinity of PLC in the presence of cassava and corn starch was 38% and 62%, respectively; a crystallinity greater than that of PCL was related to an improved nucleation at the interface. Based on these properties, the blends are expected to be functional for the manufacture of short-term use products by conventional thermoplastic processing methods.
The use of biomaterials as a replacement for thermoplastic polymers is an environmentally sound strategy. In this work, hydrogels of cellulose isolated from wheat husk were modified by UV irradiation (353 nm) to improve mechanical performance. The cellulose was dissolved with a solvent system N,N-dimethylacetamide/lithium chloride (DMAc/LiCl). Infrared spectroscopy showed that the peak height at 1016 cm−1, associated with the C–O bonds of the glycosidic ring, increases with irradiation time. It was determined that the increase in this signal is related to photodegradation, the product of a progressive increase in exposure to UV radiation. The viscoelastic behavior, determined by dynamic mechanical analysis and rotational rheometry, was taken as the most important parameter of this research, showing that the best results are recorded with 15 min of UV treatment. Therefore, at this time or less, the chemical crosslinking is predominant over the photodegradation, producing an increase in the modules, while with 20 min the photodegradation is such that the modules suffer a significant reduction.
The importance of biomarker quantification in technology cannot be overstated. It has numerous applications in medical diagnostics, drug delivery, and the timely implementation of prevention and control strategies for highly prevalent diseases worldwide. However, the discovery of new tools for detection has become increasingly necessary. One promising avenue is the use of perovskite-based materials, which exhibit excellent catalytic activity and redox properties. These make them ideal candidates for the development of electrochemical sensors. In this review, the advances of purely non-enzymatic electrochemical detection of bio-analytes, with ABO3 perovskite form, are presented. The work allows the visualization of some of the modifications in the composition and crystal lattice of the perovskites and some variations in the assembly of the electrodes, which can result in systems with a better response to the detection of analytes of interest. These findings have significant implications for improving the accuracy and speed of biomarker detection, ultimately benefiting patients and healthcare professionals alike.
The composites were fabricated under a variety of different process conditions, ranging from a blend of a low-density polyethylene reinforced with agave bagasse fibers at concentrations of 5, 10 up to 20 wt%. The theoretical and experimental moduli were determined in conjunction with the fiber degradation. The results show that the moduli of the composites increased with fiber content but decreased linearly with increasing processing temperatures. The calculated theoretical module with the Cox model is significantly greater than that experimentally obtained due to the fiber degradation, poor interfacial fiber/polymer interaction, and structural defects in the interior of the composite generated by the thermal conditions. Thermogravimetric analysis shows an unexpected three-stage process of degradation of the fiber in the temperature range of 225–290℃.
This study explores the development of a non-enzymatic electrochemical glucose sensor based on poly(3-aminobenzoic acid) (P3ABA) combined with silver nanoparticles (AgNPs). Incorporating AgNPs into the P3ABA matrix enhances the sensor’s electrocatalytic properties, leading to a system with greater stability. Cyclic voltammetry and chronoamperometry were employed to evaluate the sensor’s performance, demonstrating a sensitivity of 50.71 µA mM−1 cm−2 and a limit of detection (LOD) of 0.2 µM. The sensor exhibited a linear response over a broad concentration range (1 to 16 mM), with a coefficient of determination (R2) of 0.998, indicating good reproducibility and precision. These results highlight the potential of the P3ABA/AgNP composite for glucose sensing applications, offering an extended linear range, allowing for the quantification of glucose concentrations from very low to significantly high levels, covering both physiological and pathological conditions.
The present work describes the synthesis of an electroactive nanocomposite consisting of carbon black (CB) and polyaniline (PANI) obtained by in situ oxidative polymerization. Monomer P1 was used as a polyaniline precursor. P1 has surfactant properties that allow obtaining core–shell structures dispersed in an aqueous medium. The nanocomposite, together with silver nanoparticles (AgNPs) as an electrocatalytic element, was used to modify the surface of a glassy carbon electrode (GCE) for glucose detection. Electroactive areas were calculated using the Randles–Sevick equation. The results showed that the CB-PANI.1-1/AgNP nanocomposite exhibited a larger electroactive surface area (0.3451 cm2) compared to AgNP alone (0.0973 cm2) or the CB-PANI.1-1 composite (0.2989 cm2). Characterization of CB-PANI.1-1/AgNP, by cyclic voltammetry in the presence of glucose, showed a new oxidation peak with a maximum current close to 0.7 V due to the oxidation of glucose to gluconolactone. The amperometry test at 0.7 V showed a linear response with R2 of 0.999 as a function of the analyte concentration. The glucose sensor presented a linear detection range of 1 to 10 mM, a sensitivity of 41 µA mM−1 cm−2, and a limit of detection (LOD) of 520 µM.