Arash Shams taleghani

Dr. Arash Shams taleghani

Aeronautical, Aerospace Research Institute, Tehran, Tehrān, Iran
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 April 2022 in Flow, Turbulence and Combustion
Verified
Journal Article
Closed access
PDF file
SASoheila Abdolahipour
Soheila Abdolahipour
MMMahmoud Mani
Mahmoud Mani
ATArash Shams taleghani
Arash Shams taleghani

1 September 2022 in Journal of Aerospace Engineering
Verified
Journal Article
Closed access
PDF file
SASoheila Abdolahipour
Soheila Abdolahipour
MMMahmoud Mani
Mahmoud Mani
ATArash Shams taleghani
Arash Shams taleghani
In this paper, the potential of a novel active flow control strategy by means of a modulated pulse jet vortex generator to enhance high-lift performance is demonstrated on a two-dimensional supercritical National Aeronautics and Space Administration (NASA) SC(2)-0714 airfoil with a single slotted trailing-edge flap at a high deflection angle. Fast-switching solenoid valves and compressed air were used as actuators to excite the flow. The vortex generator slot pairs were incorporated into the shoulder of the trailing-edge flap, where the flow separation occurs due to the high flow deflection and severe adverse pressure gradient. In these experiments, in addition to the simple square-wave excitation signal, a burst-modulated excitation signal as a novel pulse jet sequence was implemented to produce the unsteady blowing. The burst-modulation signal was used for the first time for a fast-switching solenoid valve actuator. The experiments were performed at a freestream velocity of 25  m/s with a corresponding Reynolds number of about 1×106 for a range of angles of attack from 0° to 20° at flap deflection angles from 0° to 35°. The results indicated that the ejection from vortex generator slot pairs was able to prevent flow separation completely in most conditions. These measurements revealed that the burst-modulated excitation was accompanied by more aerodynamic improvements and less air consumption relative to the simple pulsed jet excitation. In the best flow control mode, the results showed about a 12.6% increase in the lift coefficient and a 19.8% decrease in the drag coefficient.

11 October 2021 in Physica Scripta
Verified
Journal Article
Closed access
PDF file
SASoheila Abdolahipour
Soheila Abdolahipour
MMMahmoud Mani
Mahmoud Mani
ATArash Shams taleghani
Arash Shams taleghani
Recently, pulsed jet actuators have been discovered as an efficient and promising technique for flow separation control. In this paper, a systematic experimental investigation is carried out using a flow control approach, in order to study the flow field characteristics of a baseline single pulsed jet actuator, under different excitation conditions. The findings are used to provide a better understanding of pulsed blowing actuator operation and the associated flow physics. In these experiments, two types of signal waveforms have been implemented to produce the pulsed excitation of jet; a simple square-wave excitation signal for the first case and a burst modulated excitation signal for the second case. All measurements were conducted using a single hot-wire system to an axial distance x/D ≤ 30 along the centerline. The effects of electrical parameters on properties of a single pulsed jet, including the excitation frequency from 10 up to 220 Hz and the duty cycle from 15% up to 80% for the first case, and different combinations of the carrier frequency and the modulating frequency for the second case have been studied. These measurements revealed a significant dependence of mean centerline velocity and turbulence intensity to excitation signal, frequency, and duty cycle. The statistical flow properties, such as mean centerline velocity decay and turbulence intensity distribution of pulsed jets are quantified and compared together over a wide range of pulsing parameters. This investigation aids in designing and optimizing flow control actuators in aerodynamics and combustion chambers.

15 March 2018 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
ATArash Shams taleghani
Arash Shams taleghani
ASAbdollah Shadaram
Abdollah Shadaram
MMMasoud Mirzaei
Masoud Mirzaei
SASoheila Abdolahipour
Soheila Abdolahipour

8 September 2013 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
MMMorteza Mohammadi
Morteza Mohammadi
ATArash Shams taleghani
Arash Shams taleghani

17 September 2013 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
ASAtefeh Salmasi
Atefeh Salmasi
ASAbdollah Shadaram
Abdollah Shadaram
ATArash Shams taleghani
Arash Shams taleghani
One of the new techniques in active flow control is the single-dielectric barrier discharge plasma actuator, which postpones the separation with external momentum injection to the boundary layer flow. In this paper, the effect of the presence of a plasma actuator on the passing flow is investigated both numerically and experimentally at a poststall angle of attack NLF0414 airfoil. These investigations are performed for a 45-cm cord NLF0414 airfoil with an incompressible 25-m/s velocity airflow, which provides a turbulent flow. Both numerical and experimental studies are done under the same conditions for two different cases: 1) no plasma actuator is located on the airfoil and 2) a plasma actuator is located on the top surface of the airfoil. Simulating the flow over the airfoil with the presence of a plasma actuator at 9.6 mm from the leading edge of the airfoil showed that the numerical distribution of the body force induced by the plasma actuator (computed using the model presented by Suzen ) is in an appropriate correlation with the experimental results. It has been also shown that the presence of the plasma actuator on the airfoil could delay the separation and subsequently increase the airfoil's efficiency. Initially, the experimental and numerical results were compared and the written code, for simulation of the body force produced by the plasma actuator was verified. Then, the effect of the plasma actuator's location on the separation's delay at different angles of attack was numerically studied. In this case, the place of the plasma actuator on the airfoil was changed and its effect on postponement of the separation point was investigated. The results show that when the actuator is placed exactly at the leading edge of the airfoil, it has the greatest influence on postponing the separation. In addition, at an angle of attack of 18 ° , it transfers the separation point from 16 to 90 mm. In addition, it results in an increase of ~ 100% in the efficiency (the ratio of lift to drag coefficient) of the airfoil at this angle of attack.