Joseph Asante

Prof. Joseph Asante

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 March 2012 in Discover Nano
Verified
Journal Article
Open access
PDF file
GNGebhu F Ndlovu
Gebhu F Ndlovu
WRWiets D Roos
Wiets D Roos
ZWZhiming M Wang
Zhiming M Wang
Joseph AsanteJoseph Asante
Joseph Asante
MMMatete G Mashapa
Matete G Mashapa
KHKenneth T Hillie
Kenneth T Hillie
The growth of three-dimensional ultra-fine spherical nano-particles of silver on few layers of graphene derived from highly oriented pyrolytic graphite in ultra-high vacuum were characterized using in situ scanning tunneling microscopy (STM) in conjunction with X-ray photoelectron spectroscopy. The energetics of the Ag clusters was determined by DFT simulations. The Ag clusters appeared spherical with size distribution averaging approximately 2 nm in diameter. STM revealed the preferred site for the position of the Ag atom in the C-benzene ring of graphene. Of the three sites, the C-C bridge, the C-hexagon hollow, and the direct top of the C atom, Ag prefers to stay on top of the C atom, contrary to expectation of the hexagon-close packing. Ab initio calculations confirm the lowest potential energy between Ag and the graphene structure to be at the exact site determined from STM imaging.

6 May 2023 in Journal of Fire Sciences
Verified
Journal Article
Open access
VMVincent N Mokoana
Vincent N Mokoana
Joseph AsanteJoseph Asante
Joseph Asante
OOO Jonathan Okonkwo
O Jonathan Okonkwo
Polymeric textile materials, now, find extensive application in modern society than previously imagined, particularly in protective clothing. The application of these polymeric materials has been restricted by their flammability and contribution to fire risk. Flame retarding compounds and inherent flame-retardant materials have been introduced to reduce and even halt the flammability of polymers. However, over time, flame retardants tend to leach out of materials. The exposure of polymer textile to varying heat intensities may trigger polymer and flame retardant’s volatilization and thermal degradation. Firefighters may be exposed to toxic chemicals through the volatilization of flame-retardant compounds from the bunker gear. Flame retardant’s volatilization is associated with thermal degradation of the flame-retardant chemical compounds in the textile material. This review focuses on volatilization of flame retardants from protective textile materials resulting from exposure to heat and seeks to provide the necessary understanding about the release of flame retardants from flame-retardant textiles, particularly firefighting garments.

15 April 2021 in Journal of Fire Sciences
Verified
Journal Article
Closed access
PDF file
Vincent MokoanaVincent Mokoana
Vincent Mokoana
Joseph AsanteJoseph Asante
Joseph Asante
JOJonathan Okonkwo
Jonathan Okonkwo
Firefighting bunker gear is manufactured from flame-retardant materials, which resist ignition and delay flame spread. However, concerns have been emerging on the potential harmful effects of some flame retardants (FRs) commonly used in flame-retarding materials, particularly the brominated flame retardants. This study investigated the presence of flame retardants in bunker gear, particularly polybrominated diphenyl ethers and their congeners in the garments, and evaluated their impact on thermal performance. X-ray fluorescence spectroscopy was used to ascertain the presence of bromine as a possible indicator for brominated flame retardants. X-ray fluorescence results indicated the presence of Br in all samples, ranging from 444 to 20,367 µg/g. Further analysis via gas chromatography–mass spectrometry was done on samples. Brominated flame retardants, particularly polybrominated diphenyl ethers and hexabromocyclododecane, were detected in all samples with concentrations ranging from 261.61 to 1001.77 µg/g and 0.01 to 0.07 µg/g, respectively. The cone calorimeter was used, with 50 and 75 kW/m2 heat fluxes, to investigate the impact of the brominated flame-retardant concentrations, if any, on thermal performance. New bunker garments, particularly those with lower Br and brominated flame-retardant concentrations, were observed to have higher thermal performance.

19 September 2016 in International Journal of Polymer Science
Verified
Journal Article
Open access
PDF file
Joseph AsanteJoseph Asante
Joseph Asante
FMFortunate Modiba
Fortunate Modiba
BMBonex Mwakikunga
Bonex Mwakikunga
Combustion measurements, such as heat release rate, critical flux, time-to-ignition, ignition temperature, thermal inertia, and kinematics—activation energy as well as preexponential factor—on epoxy polymer (Prime™20LV) with expandable graphite (EG) inorganic filler of different weight percentage composites, are conducted using the Dual Cone Calorimeter, the thermogravimetric analysis (TGA), and Linseis (Germany) THB100 Transient Hot Bridge thermal conductivity analyser. The results indicate that increasing the amount of EG in polymer composite leads to reduction in the critical flux, the time-to-ignition, the ignition temperature, the thermal inertia, the average thermal conductivity, and the activation energy (from 159.1 ± 2.3 to 145.9 ± 3.1 kJ/mol for neat epoxy to 3 wt.% EG-epoxy) of the composite samples. There is, however, an increase in the heat of gasification with increasing EG content.

18 February 2025 in Fire
Verified
Journal Article
Open access
PDF file
TMTebogo Maake
Tebogo Maake
Joseph AsanteJoseph Asante
Joseph Asante
WMWashington Mhike
Washington Mhike
BMBonex Mwakikunga
Bonex Mwakikunga
A demand to replace an easily combustible wood with wood–plastic–rubber composite with better thermal performance than wood is at its peak globally. Wood-based composite materials in the form of wood–polymer composite (WPC) have emerged as new materials that can replace wood to produce wood products for various use. The use of recycled polymers as biodegradable polymer blended with fiber particles, waste tire powder, and other substances to manufacture new products known as wood–rubber–plastics composite (WRPC) for building construction and other different applications, has piqued the interest of numerous researchers. High flammability and weak combustibility parameters are a setback for many wood-based composites because of the flammability of these composites. Fabricated WRPC based on non-toxic fire retardants and other additives used to modify the flame-resistant quality of these composites, the fabrication techniques, and mechanical characteristics are herein reviewed. It is hoped that better composite in the form of WRPC can be used as building materials for informal and formal dwellings.

15 July 2020 in Journal of Fire Sciences
Verified
Journal Article
Closed access
PDF file
TMTebogo Maake
Tebogo Maake
Joseph AsanteJoseph Asante
Joseph Asante
BMBonex Mwakikunga
Bonex Mwakikunga
The effect of fire or heat and the associated fire hazards of South African hardwoods had been minimally researched. Quantitative investigations on fire performances of selected and common South African hardwood species that include Leadwood ( Combretum imberbe), Mopani ( Colophospermum mopane), Tamboti ( Spirostachys Africana), Stinkwood ( ocotea bullata), and Real Yellowwood ( Podocarpus latifolius) were undertaken using the cone calorimeter and the thermal gravimetric analysis instrument. The results indicated that Leadwood has the superior thermal performance. It has the lowest peak heat release rate (first peak at 156 kW/m2) at external heat irradiation flux of 75 kW/m2, highest thermal response parameter (376.2 kW s1/2/m2), highest thermal inertial (11.5 kW2 s/K2 m4), highest [ ], lowest fire growth index (derived from first heat release rate peak at 3120 W/s) and lowest smoke growth index (derived from first smoke production rate peaks at 0.760 m2/s2), and lowest smoke release (toxicity) 446.5 kg/kg. Bad thermal performance wood species are Mopani and Real Yellowwood. Stinkwood on the other hand has the best thermal stability from activation energy measurements.