Aydin Ulus

Mr. Aydin Ulus

Material Science Program, Youngstown State University, Youngstown, Ohio, USA
orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 June 2025 in Energies
Verified
Journal Article
Open access
PDF file
AUAydin Ulus
Aydin Ulus
SMStefan Moldovan
Stefan Moldovan
This study introduces an innovative set of guide vanes that increase the efficiency of Vertical Axis Wind Turbines (VAWT) using winds generated by vehicles traveling on highways. The increase in efficiency is based on enhancing the airflow interaction as the vehicle moves past the turbine. Initial Computational Fluid Dynamics (CFD) simulations with two guide vanes setups demonstrated a 56.81% increase in power output under wind generated by passenger vehicles. Further design enhancements, incorporating three guide vanes with optimized geometries, led to a 242% improvement in power generation. Additional simulations evaluated the performance under wind conditions generated by larger vehicles, such as buses. The three guide vanes configuration yielded a 102% increase in energy capture efficiency in these scenarios. The findings suggest that vehicle-induced winds—typically an untapped energy source—can be effectively harvested using tailored turbine system designs. By integrating passive flow control strategies such as guide vanes, VAWTs can operate more efficiently in highway environments. This research highlights a novel pathway for enhancing renewable energy systems and supports broader efforts toward sustainable energy development through the utilization of unconventional wind sources. This performance enhancement is primarily due to the aerodynamic redirection of airflow toward the advancing blade and away from the returning blade, reducing drag and improving torque generation.

23 April 2026 in Energy Science & Engineering
Verified
Journal Article
Open access
PDF file
AUAydin Ulus
Aydin Ulus
SMStefan Moldovan
Stefan Moldovan
Vehicle wakes generate short but energetic gusts that can be used by small roadside turbines, yet the operating conditions that allow a rotor to take full advantage of these events are still not fully clear. Flow‐guiding structures that were previously shown to improve wake redirection and energy capture are employed in this study. However, the combined influence of blade count and prescribed rotational speed under true transient vehicle‐induced inflow has not been examined in a systematic way. In the present study, vertical‐axis turbines with two to six blades were evaluated numerically while a car traveling at 32 m/s produced the unsteady wake. The rotor speed was increased from the nominal value ω₀ = 6.677 rad/s (63.76 rpm, corresponding to a baseline tip‐speed ratio of approximately 0.10) up to 2.2ω₀. The results show a strong dependence of performance on both blade number and rotational speed. The two‐blade configuration provided the most consistent energy extraction and reached a maximum of 158.5 J at 2.1ω₀, representing a 24.5% increase relative to baseline speed. In contrast, higher‐solidity rotors experienced significant performance deterioration at elevated speeds, and several cases produced negative net energy. This behavior was linked to repeated interception of the wake core by returning blades at unfavorable angular positions, leading to transient torque reversal. The findings suggest that, under short‐duration vehicle wakes, low‐solidity rotors operated at carefully selected rotational speeds are more reliable than higher‐blade‐count configurations.

15 September 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
AUAydin Ulus
Aydin Ulus
IUIhsan Uluocak
Ihsan Uluocak
NVNegar Vakili
Negar Vakili
YYYoungjik Youn
Youngjik Youn
KCKyosung Choo
Kyosung Choo
Free-surface liquid jet impingement can provide high local cooling rates, but its use with hybrid nanofluids remains poorly documented. This study develops CFD-informed machine-learning surrogates for an axisymmetric free-surface jet impinging on a uniformly heated target. The volume-of-fluid model was validated against water-jet measurements, giving mean deviations of 3.0% for the radial Nusselt-number distribution and 3.3% for the stagnation-point Nusselt number across four Reynolds numbers. The database contains 91 CFD cases covering deionized water, Al₂O₃/water, TiO₂/water, and a 1:1 Al₂O₃–TiO₂/water hybrid at total particle loadings of 1–4 vol.% and Reynolds numbers of approximately 4,234–10,590. Wall temperature, heat transfer coefficient, and local Nusselt number were extracted at r/D=0, 2, 4, and 6 , yielding 364 observations. MLP, SVR, and CNN–LSTM models were evaluated using case-grouped cross-validation. MLP produced the highest R2 values for wall temperature, heat transfer coefficient, and Nusselt number, with values of 0.999, 0.998, and 0.997, respectively. CNN–LSTM ranked second, while SVR showed larger prediction errors. Permutation analysis identified Reynolds number as the dominant input, followed by radial position; composition effects were smaller. Physically constrained response maps within the sampled flow and composition ranges showed that increasing Reynolds number produced the largest thermal improvement, while nanoparticle composition provided a secondary adjustment. The surrogate models therefore provide a rapid screening tool within the investigated parameter range.

1 January 2026 in International Journal of Energy Research
Verified
Journal Article
Open access
AUAydin Ulus
Aydin Ulus
KAKhaled I. Alsharif
Khaled I. Alsharif
KCKyosung Choo
Kyosung Choo
This study presents a 28‐case computational fluid dynamics (CFD) parametric investigation of Al 2 O 3 /water and Al 2 O 3 –TiO 2 /water hybrid nanofluid cooling for an LG Chem 15 Ah lithium‐ion pouch cell subjected to a prescribed steady thermal load of 277.5 W. The imposed load is used as a severe thermal‐stress condition for coolant comparison and is not interpreted as the electrochemical heat generated by the cell at a specific C‐rate. Four Reynolds numbers (Re = 2300–10,000) and three particle volume fractions (1%, 2%, and 4%) were examined in ANSYS Fluent. The Re = 2300 cases were solved as laminar, whereas Re = 4434, 7000, and 10,000 employed the realizable k–ε model with enhanced wall treatment. Nanofluid properties were estimated using a single‐phase effective‐property approach with Maxwell thermal conductivity and Brinkman viscosity correlations. The battery‐side thermal model was compared with FLIR thermography at 32 W under natural convection; this comparison supports the hotspot location and cell‐level temperature pattern but is not presented as forced‐convection nanofluid validation. Reynolds number remained the dominant control parameter. At Re = 2300, the 4% hybrid nanofluid reduced the maximum hotspot temperature by 8.1°C relative to water and increased the bulk‐temperature‐based heat‐transfer coefficient by ~13.1%. For the turbulent cases, all nanofluids produced PEC values below unity, while at Re = 2300 the PEC values were effectively unity (0.997–1.003). Above Re = 7000, the predicted temperature advantage of nanofluid addition decreased below 0.9°C. The results indicate that hybrid nanofluids primarily provide incremental hotspot reduction at low‐to‐moderate Reynolds numbers, whereas water remains the stronger thermal‐hydraulic baseline over the turbulent range.

9 September 2026 in Energy Science & Engineering
Verified
Journal Article
Open access
AUAydin Ulus
Aydin Ulus
The effect of inlet turbulence intensity (TI) on the aerodynamic performance of a three‐bladed H‐type Darrieus vertical‐axis wind turbine with NACA 0021 blades was investigated using two‐dimensional (2D) unsteady Reynolds‐averaged Navier–Stokes (URANS) simulations. The realizable model was applied across six TI levels (TI = 1–25%) and five tip speed ratios at a freestream velocity of 9 m/s, producing 30 simulation cases. Validation against the experimental data of Castelli et al. gave a peak‐power coefficient deviation of 3.7% at λ = 2.5. The optimal operating point remained fixed at λ = 2.5 regardless of inlet turbulence, where the power coefficient decreased by 6.0% as TI increased from 5% to 25%. At λ = 1.5, the same increase in turbulence reduced the power coefficient by 17%. A modest nonmonotonic response occurred at , where the power coefficient at TI = 15% was 1.5% higher than the TI = 5% reference value. Instantaneous vorticity contours indicated increasingly diffuse wake structures at higher turbulence intensities. However, these single‐phase contours were insufficient to determine blade‐resolved separation, reattachment, or dynamic‐stall behavior. Within the present 2D framework, the peak‐power condition remained at across the investigated turbulence intensities. Further three‐dimensional analysis is required to determine whether these trends persist for a finite‐span rotor.

4 October 2026 in Energy Science & Engineering
Verified
Journal Article
Open access
PDF file
AUAydin Ulus
Aydin Ulus
SMStefan Moldovan
Stefan Moldovan
Highway‐induced airflow generated by passing vehicles represents an underutilized source of localized renewable energy that can be harvested using vertical‐axis wind turbines (VAWTs). While prior studies have demonstrated the feasibility of single‐turbine configurations, the aerodynamic interaction between vehicle wakes and multi‐turbine arrays—particularly the role of inter‐turbine spacing—remains insufficiently understood. In this study, two‐dimensional unsteady Reynolds‐averaged Navier–Stokes (URANS) simulations coupled with the SST k–ω turbulence model are employed to investigate the performance of guided elliptical Savonius‐type VAWT arrays operating under multi‐vehicle traffic conditions. Three‐turbine arrays are examined at normalized inter‐turbine spacings from S/D = 3 to 14, together with an additional phase‐aligned reference case at S/D = 30.114. The results reveal a strong non‐linear dependence of array‐level energy extraction on turbine spacing. Among the investigated configurations, the highest total energy capture is achieved at a spacing of 12 m (12D), yielding a total extracted energy of 697.34 J and representing a 68% increase relative to the most compact configuration. Smaller spacings are characterized by severe wake interference between turbines, whereas larger spacings exhibit progressive dissipation of vehicle‐induced flow structures despite near‐complete velocity recovery. Turbine 1 shows limited sensitivity to spacing, with an energy variation of approximately 14%, whereas Turbines 2 and 3 exhibit substantially greater variations of approximately 87% and more than 140%, respectively. The inclusion of guide vanes further enhances total energy extraction by approximately 80–120% across the investigated spacing range. These findings highlight the importance of coordinated inter‐turbine spacing and flow‐guiding strategies in maximizing energy harvesting from vehicle‐induced wakes and provide practical design guidance for the deployment of guided VAWT arrays in highway environments.