Bing Wu

Prof. Dr. Bing Wu


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 April 2019 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
PDF file
Bing WuBing Wu
Bing Wu
BABoyang An
Boyang An
ZWZefeng Wen
Zefeng Wen
WWWenjian Wang
Wenjian Wang
TWTao Wu
Tao Wu
The objective of this paper is to ascertain the wheel–rail low adhesion mechanism using a high-speed wheel–rail rolling contact test rig under different interfacial contaminations. Based on the experimental results, a numerical method was proposed to investigate the wheel–rail wear and rolling contact fatigue due to low adhesion issues. The experimental results indicated that the wheel–rail low adhesion phenomena can happen under interfacial liquid contaminations, especially at high-speed running condition. Preliminary numerical investigations showed that the low adhesion condition can easily lead to sliding hence serious wear, especially at the speed between 160 km/h and 200 km/h. The temperature rise within the contact patch can be significantly more severe once wheel and rail are in full slip, causing rolling contact fatigue due to material softening.


19 September 2017 in Lubrication Science
Verified
Journal Article
Closed access
PDF file
Bing WuBing Wu
Bing Wu
MCMing Chen
Ming Chen
TWTao Wu
Tao Wu
ZWZefeng Wen
Zefeng Wen
XJXuesong Jin
Xuesong Jin

9 November 2020 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Verified
Journal Article
Closed access
PDF file
GXGuangwen Xiao
Guangwen Xiao
LXLei Xu
Lei Xu
Bing WuBing Wu
Bing Wu
LYLinquan Yao
Linquan Yao
ZXZhou Xin
Zhou Xin
The aim of this paper is to investigate the dynamic response of the resilient wheel equipped on the intercity train at the rail weld. A vehicle-track coupling dynamics model with resilient wheels is developed. A rigid multi-body system with 55 degrees of freedom is utilized to model the vehicle system. The rubber layer of the resilient wheel is modeled as a three-directional spring-damper unit between the wheel rim and the wheel core. For the track sub-model, the rails were modelled as Euler Beam and supported by concrete sleepers modelled as mass block. The vehicle and track motion equations are represented as mass-stiffness-damping matrixes. The accuracy of this modeling method at low frequencies is verified via the comparison between the field measured data and numerical results. The dynamic results of the rigid wheel are compared with those of the resilient wheel. Results show that the dynamic wheel-rail force of the rigid wheel is slightly higher than that of the resilient wheel. Furthermore, the mass factor is introduced to investigate the effect of the rubber layer position on the tire acceleration and the wheel-rail impact force. The numerical simulation results are expected to provide references for resilient wheel application into the intercity train.

17 September 2023 in Lubrication Science
Verified
Journal Article
Closed access
JHJiaqing Huang
Jiaqing Huang
Bing WuBing Wu
Bing Wu
GXGuangwen Xiao
Guangwen Xiao
QSQuan Shen
Quan Shen

1 February 2025 in Physics of Fluids
Verified
Journal Article
Closed access
ZWZhaoyang Wang
Zhaoyang Wang
Bing WuBing Wu
Bing Wu
JHJiaqing Huang
Jiaqing Huang
Yuanjin JiYuanjin Ji
Yuanjin Ji
DLDingkang Li
Dingkang Li
SWShuai Wu
Shuai Wu
Wheel–rail rolling contact is a complex tribological issue, especially the existence of a thin water film on the rail surface, which leads to low adhesion problems for the traction and braking performance of the railway trains. The objective of this paper is to propose a non-Hertzian dynamic wheel–rail adhesion model for trains passing through wet curved tracks considering wheel–rail surface roughness. A vehicle-track coupling dynamics model was first developed to output the wheel–rail dynamic contact parameters under wet conditions. These parameters were subsequently utilized as dynamic inputs for the present wheel–rail adhesion model to simulate dynamic curve passing. The present numerical model includes the normal contact model and tangential model. For the normal contact issue, an elastohydrodynamic lubrication model was used to accurately determine the normal contact stress within the contact patch along the contact traces. Based on the normal contact characteristics, the advanced extended creep force model was used to compute the tangential stress. Finally, the dynamic wheel–rail adhesion coefficient can be obtained. This model considers the effects of time variation and changes in contact geometry, resulting in sudden increases or decreases in the adhesion coefficient at certain locations. At a speed of 400 km/h, a higher spin creepage occurs, leading to an increased displacement of the third-body layer and causing the maximum tangential stress to shift from one side of the contact patch to the other. Under the combined influence of the creepages, the maximum tangential stress occurs at the trailing edge of the contact patch.