Chandramouli Sangeetham

Mr. Chandramouli Sangeetham


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 May 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
MPMookkan Periyasamy
Mookkan Periyasamy
AMAa Mubasshir
Aa Mubasshir
SKStiven Kodra
Stiven Kodra
CSChandramouli Sangeetham
Chandramouli Sangeetham
RCRON CAMPBELL
RON CAMPBELL
JMJoey L. Mead
Joey L. Mead
This work investigated material extrusion additive manufacturing (MatEx AM) of specialized fluoroelastomer (FKM) compounds for applications in rubber seals and gaskets. The influence of a commercially available perfluoropolyether (PFPE) plasticizer on the printability of a control FKM rubber compound was studied using a custom-designed ram material extruder, Additive Ram Material Extruder (ARME), for printing fully compounded thermoset elastomers. The plasticizer’s effectiveness was assessed based on its ability to address challenges such as high compound viscosity and post-print shrinkage, as well as its impact on interlayer adhesion. The addition of the PFPE plasticizer significantly reduced the FKM compound’s viscosity (by 70%) and post-print shrinkage (by 65%). While the addition of the plasticizer decreased the tensile strength of the control compound, specimens printed with the plasticized FKM retained 34% of the tensile strength of compression-molded samples, compared to only 23% for the unplasticized compound. Finally, the feasibility of seals and gaskets manufacturing using both conventional and unconventional additive manufacturing (AM) approaches was explored. A hybrid method combining AM and soft tooling for compression molding emerged as the optimal method for seal and gasket fabrication.

23 February 2026 in Polymers
Verified
Journal Article
Open access
PDF file
AMAA Mubasshir
AA Mubasshir
SKStiven Kodra
Stiven Kodra
CSChandramouli Sangeetham
Chandramouli Sangeetham
DKDavid Kazmer
David Kazmer
JMJoey L. Mead
Joey L. Mead
While the effects of formulation variables of a rubber compound are well established for conventional rubber manufacturing techniques, their role in extrusion-based additive manufacturing remains underexplored. This study explores the impact of different base rubbers (NBR and EPDM) and curing agents (sulfur and peroxide) on processability and final part characteristics in material extrusion additive manufacturing applications. Under identical printing conditions, sulfur-cured NBR exhibits greater post-print shrinkage (12%) than sulfur-cured EPDM (7%). However, sulfur-cured NBR achieves a higher degree of adhesion between printed layers than sulfur-cured EPDM, as suggested by the % retention of the bulk materials’ ultimate stress by the printed parts (84–100% and 51–62%, respectively). Additionally, a peroxide-cured NBR formulation was compared against the same sulfur-cured NBR formulation. Printed parts from the peroxide-cured NBR formulation showed higher shrinkage (16%) and lower % retention of the bulk materials’ ultimate stress (26–33%) than the sulfur-cured NBR formulation. Additionally, the tensile behavior of all three rubber compounds was found to be strongly dependent on printing orientation, showing the anisotropic behavior typical of extrusion-based additive manufacturing. Sulfur-cured NBR showed the least anisotropy for stress at break (0.82) and strain at break (0.90), whereas peroxide-cured NBR showed the highest anisotropy in stress (0.74) and strain (0.82). The anisotropy ratios for sulfur-cured NBR and EPDM compounds were very similar for stress (0.82 vs. 0.82) and comparable for strain (0.90 vs. 0.87). Notably, the peroxide cure system provided almost twice as much available printing time as the sulfur cure system. This report on the effects of base rubber and curing agents on 3D printability and part properties provides a background to guide future efforts to design rubber compounds for 3D printing applications.