This paper presents a novel concept of a high-voltage-gain DC-DC converter. The converter is made up of switched capacitors and passive resonant branches. A significant reduction in the count of switches and low voltage stress on the switches is achieved in this proposed converter topology, in comparison to that of a classical SC series-parallel converter. It is essential from the cost, volume, and efficiency of the converter standpoint. The reduction in the count of switches is threefold. The highest voltage stress on the switches depends on the output voltage and is decreased in the proposed converter as well, as the output voltage is divided into two series-connected capacitors. The presented results demonstrate the operation of the converter with the use of resonant branches, its switching strategies, voltage stresses of switches, efficiency, voltage gain, and output voltage regulation as well as the zero-voltage switching (ZVS) operation. The paper also presents novel issues related to analytical loss modeling, extended concepts of topology, converter start-up, and operation during transient states. The demonstrated concept of the converter, the analytical discussion and its design, as well as the experimental setup and results clearly demonstrate the optimization achievements.

This paper presents the overall concept of a wideband and cost-effective current sensor. The sensor consists of a paralleled Hall-based current sensor (LEM) and a wideband current transformer (CT). A significant improvement of the band range and the moderate cost of the proposed sensor enable it to be used both to measure the instantaneous value in order to precisely plot the current and to obtain signals for a closed-loop control system of high-frequency power electronic converters. The sensor should be considered as an Augmented LEM Current Sensor (ALCS), which allows it to measure low- and high-frequency current signals. Finally, it allows for the measurement of a bipolar current up to 40 A. The overall cost of the sensor, along with the previously mentioned benefits, is an important feature of the proposed sensor. The present paper presents the analytical concept of the sensor (ALCS), a theoretical approach using simulation analysis, and the experimental results, which clearly demonstrate the wide range of the sensor in dynamic and static measurements.

High-frequency current transformers (HFCT) are widely used to measure fast transient current. Their advantages are simple structure and relatively moderate price. Their lower and upper bandwidth are limited, but the HFCT can be easily applied to many measuring applications in power electronics. The disadvantages of HFCT are substantial dimensions and a large weight. The paper proposes a system of a cascade connection of two transformers, which allows us to reduce these disadvantages. The properties of such an HFCT combination were investigated and described. In the article, the expression for double current transformer transmittances is derived. The frequency response of the sensor was determined, and the results were verified in a practical arrangement. An experimental setup of a cascade CT connection was made and tested, allowing for fast-changing signals in transients to be measured. This paper presents the theoretical basis and results of laboratory work on a wide range of static and dynamic tests of the proposed sensor.

This paper proposes a transformerless dual half-bridge converter (TLDAHB). By eliminating the transformer and harnessing the possibility of using a low inductor value, it is possible to minimise the size of the converter. A phase-shift pulse width modulation will result in a wide controlled voltage gain of the converter and operation as buck and boost. The theoretical topology analysis, simulation, and experimental results are presented. Theoretical analysis consists of analysis of power transfer and design. In case of experimental research, particular attention was paid to power transfer and efficiency analysis. Near zero switching transient of voltage in the half-bridge topology results with high efficiency.

This elaboration presents the concept of the design, parameters, experimental investigation, and thermal numerical model solved using the finite element method of a high-power-density DC–DC converter. The analyzed unit can be utilized as a stand-alone converter or as a module for a scalable high-voltage gain system. The converter has a decreased bill of materials since it does not use typical chokes and heatsinks. It is based on switched capacitor circuits supported by a resonant choke which protects against inrush currents. A printed circuit board is utilized not only for the resonant inductance design but also for cooling transistor and diode devices. The paper demonstrates the design concept and the achieved parameters. Experimental results show heat distribution on the printed circuit board and components in a steady state and dynamical states as well. The converter parameters and their efficiency are measured as well. The convergence of experimental results and heating simulations is demonstrated. The numerical model is used for the investigation of design cases. The printed circuit board size, thermal via pattern, and heating process during the overload of the converter are investigated.

The article proposes a method of measuring losses in magnetic elements for medium-frequency power electronics, up to 200 kHz. In the method, the measurement of losses is carried out under voltage–current operating conditions of the inductive element similar to practical applications, adjustable in a wide range. A proposed three-source converter (TSC) allows one to generate proper operating conditions for the inductor. The TSC has been simulated and verified under laboratory conditions.