Christian Cobos

Dr. Christian Cobos


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 May 2019 in Rapid Prototyping Journal
Verified
Journal Article
Open access
CCChristian Cobos
Christian Cobos
LGLuis Garzón
Luis Garzón
Juan López-MartínezJuan López-Martínez
Juan López-Martínez
Octavio FenollarOctavio Fenollar
Octavio Fenollar
SFSantiago Ferrandiz
Santiago Ferrandiz
This paper aims to propose using polylactic acid (PLA) as an alternative to nanocomposites in additive manufacturing processes in fusion deposition modelling (FDM) systems and describe its thermal and rheological conditions with multi-wall carbon nanotube (PLA/MWCNT) and halloysite nanotube (PLA/HNT) composites for possible applications in additive manufacturing processes. PLA/MWCNTs and PLA/HNTs were obtained through fusion in a co-rotating twin-screw extruder. PLA was mixed with different percentages of MWCNTs and HNTs at concentrations of 0.5 Wt.%, 0.75 Wt.% and 1 Wt.%. Differential scanning calorimetry (DSC) and capillary rheometry were used to characterise these products, together with an analysis of the melt flow index (MFI). The DSC data revealed that the nanocomposites had a glass transition temperature Tg = 65 ± 2°C and a melting temperature Tm = 169 ± 1°C. The crystallisation temperature of PLA/MWCNTs and PLA/HNTs was between 107 ± 2°C and 129°C, respectively. The viscosity data of PLA/MWCNTs and PLA/HNTs obtained by capillary rheometry indicated that the viscosity of the materials is the same as that of neat PLA. These results were confirmed by the higher fluidity index in the MFI analysis. This paper presents an alternative for the applications of nanocomposites in additive manufacturing processes in FDM systems.

30 March 2020 in Rapid Prototyping Journal
Verified
Journal Article
Open access
PDF file
CCChristian Cobos
Christian Cobos
OFOctavio Fenollar
Octavio Fenollar
JMJuan López Martinez
Juan López Martinez
SFSantiago Ferrandiz
Santiago Ferrandiz
LGLuis Garzón
Luis Garzón
Purpose: This paper aims to describe the influence of maleinized linseed oil (MLO), when used as a lubricant, on the thermal and rheological properties of PLA/MWCNTs (polylactic acid/multi-walled carbon nanotubes) and PLA/HNT (halloysite nanotubes) nanocomposites, as a reference for application in 3D printing processes. Design/methodology/approach: Nanocomposites were obtained by melting in a twin-screw extruder, mixing PLA with MWCNTs and HNTs in different percentages of 0.5, 0.75 and 1 Wt.% for subsequent mixing by the same process with 5 phr MLO, for application in additive manufacturing, as analyzed by means of differential scanning calorimetry (DSC), capillary rheometry, melt flow rate (MFL) and field emission scanning electron microscopy (FESEM). Findings: The results obtained for thermal characterization by using DSC indicate the non-variation of glass transition temperature Tg = 62 ± 2°C and a melting temperature (Tm) around 170°C. Crystallization temperature dropped by approximately 12°C, which should be kept in mind during the transformation processes. The values obtained by capillary rheometry indicate that the material’s viscosity is reduced by the influence of the MLO plasticizer’s lubricant effect on the PLA’s molecular structure. The melt flow index values confirm a rise of approximately 46% in the flow index and back up the capillary rheometry results. The values obtained were as follows: PLA/0.5 Wt.% MWCNT/MLO 5 phr 54.07, PLA/0.75 Wt.% MWCNT/MLO 5 phr 53.46, PLA/1 Wt.% MWCNT/MLO 5 phr 51.84y PLA/0.5 Wt.% HNT/MLO 5 phr 61.8, PLA/0.75 Wt.% HNT/MLO 5 phr 68.3 and PLA/1 Wt.% HNT/MLO 5 phr 71.2 g/10 min. Apart from the nanocharge distribution, the information obtained from the FESEM shows the existence of a cluster, which could have been avoided by more energetic stirring during the nanocompound manufacturing process. Social implications: This paper presents an analysis of the insertion of plasticizer in nanocomposites for the application in additive manufacturing processes in fusion deposition modelling (FDM) system. Originality/value: This is a novel original research work.

3 April 2025 in Rapid Prototyping Journal
Verified
Journal Article
Open access
PDF file
CCChristian Cobos
Christian Cobos
SFSantiago Ferrandiz
Santiago Ferrandiz
LGLuis Garzón
Luis Garzón
JLJuan López
Juan López
EREmilio Rayon
Emilio Rayon
This paper aims to show the mechanical properties of neat polylactic acid (PLA) and PLA with two types of nanoparticles as reinforcement, multi-walled carbon nanotubes (MWCNT) and halloysite nanotubes (HNT) with and without maleinized linseed oil (MLO) as plasticizer, for applications in industrial models and the biomedical field, respectively. This research evaluates the mechanical response of PLA/MWCNT and PLA/HNT nanocomposites, at concentrations of 0.5 and 1Wt.%, with and without MLO plasticizer at a ratio of 5 phr, which were obtained by melting in a twin-screw extruder. The standardized specimens were manufactured on a Tumaker NX Pro 3D printer with pellets instead of filaments. The studies carried out were tensile and flexural tests, Charpy impact test, microhardness and field emission scanning electron microscope (FESEM). Tensile tests revealed that neat PLA has a tensile strength of 50.7 MPa, an elastic modulus of 1366.8 MPa and a stretch factor of 6.9%, while the values of MWCNT and HNT nanocomposites without plasticizer are 50% below these figures. The MWCNTs composites with plasticizer increase tensile strength by about 20% over neat PLA, indicating that the nanomaterials with MLO have better mechanical properties due to the plasticizing effect. Neat PLA showed a flexural strength of 93.83 MPa and a flexural modulus of 2657.51 MPa, respectively. The MWCNTs and HNTs composites without plasticizer reveal a 60% and 30% decrease compared to neat PLA, respectively. In comparison, the composites with plasticizer have no more than 10% variation concerning neat PLA. In Charpy impact tests, neat PLA absorbed 19.75 kJ/m2 of the energy in the resilience test. At the same time, MWCNTs nanocomposites without plasticizer show a substantial reduction of about 80%, and those with plasticizer absorbed about 15% less energy. HNTs nanocomposites show similar results to those of neat PLA. FESEM shows different nanocomposite fracture types, distributions and miscibility of nanoloads and plasticizer in the polymer matrix. The 20% increase in tensile strength of MWCNTs composites with plasticizer suggests their potential use for applications requiring durability, such as biomedical devices and structural components. In addition, the improved mechanical properties of the nanomaterials, especially MLO, highlight their viability for the development of conductive polymers in flexible electronics and sensors. This study explores the mechanical response of PLA/HNTs and PLA/MWCNTs nanomaterials obtained by 3D printing. It suggests their potential use as biomaterials in the biomedical field, tissue engineering, and industrial polymeric materials.

1 January 2019 in Procedia Manufacturing
Verified
Journal Article
Open access
CCChristian Cobos
Christian Cobos
ACA. Conejero
A. Conejero
OFO. Fenollar
O. Fenollar
SFS. Ferrándiz
S. Ferrándiz

27 November 2025 in Polymers
Verified
Journal Article
Open access
PDF file
CCChristian Cobos
Christian Cobos
SFSantiago Ferrandiz
Santiago Ferrandiz
EEEmilio Rayón Encinas
Emilio Rayón Encinas
LLLuis Marcelo López-López
Luis Marcelo López-López
LGLuis Garzón
Luis Garzón
Polylactic acid (PLA) is a biodegradable polymer with an ever-increasing number of applications, although its inherent brittleness limits its performance somewhat in structural applications. In this study, we analysed the influence of incorporating multi-walled carbon nanotubes (MWCNTs) and halloysite nanotubes (HNTs) at different concentrations (0.5, 0.75 and 1 wt%) on the mechanical properties of injection-moulded PLA nanocomposites. The effects of the nanofillers were characterised by tensile, flexural, and impact tests, hardness measurements, and FESEM examination. The results showed that MWCNTs increased the flexural strength and stiffness by up to 60% compared to neat PLA (84.3 vs. 52.6 MPa), although this was accompanied by a reduction in elongation at break (from 2.30% to 1.57%) due to agglomeration. Conversely, HNTs improved the elongation at break up to 6.39%, enhanced flexural strength by approximately 62% (85.1 MPa), and maintained stiffness around 3.0 GPa, indicating a better balance between strength and ductility. The FESEM micrographs confirmed the presence of clusters in MWCNTs and a more homogeneous dispersion in HNTs, thus explaining the differences in behaviour. Overall, MWCNTs are more suitable for applications requiring high stiffness and strength, whereas HNTs are preferable when greater ductility and impact resistance are required.

1 December 2025 in 3D Printing and Additive Manufacturing
Verified
Journal Article
Closed access
SOSantiago Ochoa
Santiago Ochoa
SFSantiago Ferrándiz
Santiago Ferrándiz
LGLuis Garzón
Luis Garzón
CCChristian Cobos
Christian Cobos
As additive manufacturing by fused filament fabrication has gained popularity, computational analysis has become fundamental in predicting the mechanical behavior of 3D models. This paper proposes the development of a method for the finite element (FE) simulation of 3D-printed parts, implementing model design reverse engineering using G-code to obtain their digital twins (DTs). Samples were printed under the ASTM D638 standard with different nozzle diameters and layer heights, which allowed them to be mechanically characterized by tensile tests. The tensile tests determined that the diameter of the nozzles used (between 0.2 mm and 1.0 mm) influences the material’s tensile strength. The greater the diameter, the greater the stiffness, which translates into a change in the Young’s modulus, as well as greater tensile strength and thus a reduction of the deformation, for which a value of 2.66 ± 0.6 % was obtained, i.e., the filament diameter did not influence this aspect. After carrying out the reverse engineering process of the samples to obtain DTs of the physical models, the printing G-code was used with the help of a Python script for their conversion to trajectories. These trajectories were introduced into Rhinoceros software with the Grasshopper add-on to obtain the reconstructed 3D models. The deposited filament profile used to reconstruct the DT was obtained by microscopy of the section of the physical samples. The predominant profile observed was that of a flattened oval. FE simulation was then carried out, obtaining a similarity of 90% between the simulated and mechanical tests, which validated the proposed method of predicting mechanical stresses in printed 3D elements.