Costica Bejinariu

Prof. Dr. Costica Bejinariu

Gheorghe Asachi Technical University of Iași, Iaşi, Romania
orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
AÇAli İhsan Çelik
Ali İhsan Çelik
Yasin OzkilicYasin Ozkilic
Yasin Ozkilic
Ozer ZeybekOzer Zeybek
Ozer Zeybek
MKMemduh Karalar
Memduh Karalar
SQShaker M. A. Qaidi
Shaker M. A. Qaidi
Costica BejinariuCostica Bejinariu
Costica Bejinariu
In this study, ground glass powder and crushed waste glass were used to replace coarse and fine aggregates. Within the scope of the study, fine aggregate (FA) and coarse aggregate (CA) were changed separately with proportions of 10%, 20%, 40%, and 50%. According to the mechanical test, including compression, splitting tensile, and flexural tests, the waste glass powder creates a better pozzolanic effect and increases the strength, while the glass particles tend to decrease the strength when they are swapped with aggregates. As observed in the splitting tensile test, noteworthy progress in the tensile strength of the concrete was achieved by 14%, while the waste glass used as a fractional replacement for the fine aggregate. In samples where glass particles were swapped with CA, the tensile strength tended to decrease. It was noticed that with the adding of waste glass at 10%, 20%, 40%, and 50% of FA swapped, the increase in flexural strength was 3.2%, 6.3%, 11.1%, and 4.8%, respectively, in amount to the reference one (6.3 MPa). Scanning electron microscope (SEM) analysis consequences also confirm the strength consequences obtained from the experimental study. While it is seen that glass powder provides better bonding with cement with its pozzolanic effect and this has a positive effect on strength consequences, it is seen that voids are formed in the samples where large glass pieces are swapped with aggregate and this affects the strength negatively. Furthermore, simple equations using existing data in the literature and the consequences obtained from the current study were also developed to predict mechanical properties of the concrete with recycled glass for practical applications. Based on findings obtained from our study, 20% replacement for FA and CA with waste glass is recommended.

28 December 2021 in Materials
Verified
Journal Article
Open access
PDF file
Dumitru-Doru Burduhos-NergisDumitru-Doru Burduhos-Nergis
Dumitru-Doru Burduhos-Nergis
Petrica VizureanuPetrica Vizureanu
Petrica Vizureanu
Andrei Victor SanduAndrei Victor Sandu
Andrei Victor Sandu
Diana-Petronela Burduhos-NergisDiana-Petronela Burduhos-Nergis
Diana-Petronela Burduhos-Nergis
Costica BejinariuCostica Bejinariu
Costica Bejinariu
Coal ash-based geopolymers with mine tailings addition activated with phosphate acid were synthesized for the first time at room temperature. In addition, three types of aluminosilicate sources were used as single raw materials or in a 1/1 wt. ratio to obtain five types of geopolymers activated with H3PO4. The thermal behaviour of the obtained geopolymers was studied between room temperature and 600 °C by Thermogravimetry-Differential Thermal Analysis (TG-DTA) and the phase composition after 28 days of curing at room temperature was analysed by X-ray diffraction (XRD). During heating, the acid-activated geopolymers exhibited similar behaviour to alkali-activated geopolymers. All of the samples showed endothermic peaks up to 300 °C due to water evaporation, while the samples with mine tailings showed two significant exothermic peaks above 400 °C due to oxidation reactions. The phase analysis confirmed the dissolution of the aluminosilicate sources in the presence of H3PO4 by significant changes in the XRD patterns of the raw materials and by the broadening of the peaks because of typically amorphous silicophosphate (Si–P), aluminophosphate (Al–P) or silico-alumino-phosphate (Si–Al–P) formation. The phases resulted from geopolymerisation are berlinite (AlPO4), brushite (CaHPO4∙2H2O), anhydrite (CaSO4) or ettringite as AFt and AFm phases.

9 August 2017 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
Doru-Costin DarabontDoru-Costin Darabont
Doru-Costin Darabont
AAAnca Elena Antonov
Anca Elena Antonov
Costica BejinariuCostica Bejinariu
Costica Bejinariu
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry

16 April 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Diana-Petronela Burduhos-NergisDiana-Petronela Burduhos-Nergis
Diana-Petronela Burduhos-Nergis
Petrica VizureanuPetrica Vizureanu
Petrica Vizureanu
Andrei Victor SanduAndrei Victor Sandu
Andrei Victor Sandu
Costica BejinariuCostica Bejinariu
Costica Bejinariu
This study aims to evaluate the corrosion resistance of carbon steel, used for carabiners manufacturing, coated with three different types of phosphate layer. The phosphate layers have been obtained by phosphate conversion coating with three different types of phosphate solutions: zinc-based solution, zinc-iron-based phosphate solution, and manganese-based phosphate solution. Additionally, the test was performed on zinc phosphate samples impregnated with molybdenum bisulfate-based oil and zinc phosphate samples further coated with a layer of elastomer-based paint. Considering the areas where the carabiners are used (civil engineering, navigation, oil industry, rescue operations, etc.), the corrosive environments studied are rainwater, Black Sea water, and fire extinguishing solution. The structure of the deposited layers was studied by scanning electron microscopy, while the interface structure between the alloy and corrosive environment was analyzed by electrochemical impedance spectroscopy. According to this study, the corrosion resistance of zinc-based phosphate coated samples and zinc/iron-based phosphate coated samples is higher than that of the studied carbon steel samples, despite the corrosion environment. Also, the most aggressive corrosion environment was the fire extinguishing solution.

18 July 2017 in Sustainability
Verified
Journal Article
Open access
PDF file
Costica BejinariuCostica Bejinariu
Costica Bejinariu
Doru-Costin DarabontDoru-Costin Darabont
Doru-Costin Darabont
Elena-Raluca BaciuElena-Raluca Baciu
Elena-Raluca Baciu
IGIuliana-Silvia Georgescu
Iuliana-Silvia Georgescu
MBMihai-Adrian Bernevig
Mihai-Adrian Bernevig
CBConstantin BACIU
Constantin BACIU
The application of the method for assessing the level of safety at work starts with a document that contains the cover page, the description of the company (name, location, core business, organizational chart etc.), description of the work system, a detailed list of its components, and a brief description of the assessment method. It continues with a Microsoft Excel document, which represents the actual application of the method and, finally, there is another document presenting conclusions, proposals, and prioritizations, which leads to the execution of the Prevention and Protection Plan. The present paper approaches the issue of developing the Microsoft Excel document, an essential part of the method for assessing the level of safety at work. The document is divided into a variable number of worksheets, showing the risk categories of general, specific, and management.

1 April 2013 in Surface and Coatings Technology
Verified
Journal Article
Closed access
Stefan-Lucian TomaStefan-Lucian Toma
Stefan-Lucian Toma
Costica BejinariuCostica Bejinariu
Costica Bejinariu
RBRaluca Baciu
Raluca Baciu
SRSteluta Radu
Steluta Radu