ZnO is one of the most studied oxides due to its nontoxic nature and remarkable properties. It has antibacterial and UV-protection properties, high thermal conductivity, and high refractive index. Various ways have been used to synthesize and fabricate coinage metals doped ZnO, but the sol-gel technique has received a lot of interest because of its safety, low cost, and facile deposition equipment. Coinage metals are represented by the three nonradioactive elements of group 11 of the periodic table: gold, silver, and copper. This paper, which was motivated by the lack of reviews on the topic, provides a summary of the synthesis of Cu, Ag, and Au-doped ZnO nanostructures with an emphasis on the sol-gel process and identifies the numerous factors that affect the morphological, structural, optical, electrical, and magnetic properties of the produced materials. This is accomplished by tabulating and discussing a summary of a number of parameters and applications that were published in the existing literature over the previous five years (2017–2022). The main applications being pursued involve biomaterials, photocatalysts, energy storage materials, and microelectronics. This review ought to serve as a helpful reference point for researchers looking into the many physicochemical characteristics of coinage metals doped ZnO, as well as how these characteristics vary according to the conditions under which experiments are conducted.
14 August 2018 in Journal of Thermal Analysis and Calorimetry
The effect of gel preparation and heat treatment on the structural and optical properties of SiO2-ZnO materials prepared by the sol–gel method was investigated. Zinc acetate dehydrate, TEOS (tetraethylortosilicate), ethanol, distillated water and HCl were used as a starting material, solvent and catalyst, respectively. Four powders (G1–G4) were prepared in different ways from the starting materials mentioned above. The method of adding Zn precursors during the synthesis differed from one another. For the G1 synthesis, only Zn acetate powder was employed; for the G2 synthesis, Zn acetate was dissolved in distilled water; and for the G3 synthesis, Zn acetate was dissolved in ethanol. When synthesizing G4, TEOS was added last, after Zn acetate had been combined with water and ethanol. The SiO2-ZnO materials were dried at 200 °C and then heat-treated at 700 °C and 900 °C. All samples were investigated by X-ray diffraction and infrared spectroscopy in order to investigate their structure. SEM measurements were performed to investigate the morphology of materials. Optical properties were influenced by gel preparation and heat treatments. A reflectance of over 60% was obtained for G3 and G4 powders, while for G1 and G2, the reflectance was below 30%. In conclusion, synthesis steps and heat treatment can control the structure and properties of the powders.
In this paper, we conducted a fundamental study concerning the effect of thermal treatment on the structure and morphology of 2 mol% vanadium doped ZnO nanopowders obtained by microwave assisted sol–gel method (MW). The samples were analyzed by DTA, FTIR, XRD, SEM, and UV–Vis spectroscopy. The DTA results showed that above 500 °C, there was no mass loss in the TG curves, and ZnO crystallization occurred. The XRD patterns of the thermally treated powders at 500 °C and 650 °C showed the crystallization of ZnO (zincite) belonging to the wurtzite-type structure. It was found that in the 650 °C thermally treated powder, aside from ZnO, traces of Zn3(VO4)2 existed. FTIR spectra of the annealed samples confirmed the formation of the ZnO crystalline phase and V–O bands. The micrographs revealed that the temperature influenced the morphology. The increase in the annealing temperature led to the grain growth. The SEM images of the MW powder thermally treated at 650 °C showed two types of grains: hexagonal grains and cylindrical nanorods. UV–Vis spectra showed that the absorption band also increased with the increasing temperature of thermal treatment. The MW sample annealed at 650 °C had the highest absorption in ultraviolet domain.
Thermal energy storage is at the leading edge of various applications, including waste heat recovery, solar storage and zero-energy buildings. Phase change materials (PCMs) can be utilized to store heat through reversible solid–liquid phase transitions. PCMs provide high energy storage capacity at a constant temperature. The volume change during the phase transition, on the other hand, causes inconsistency in crystallization and leakage, increasing the system’s complexity and shortening the lifetime of these materials. These shortcomings can be diminished by impregnation in a porous matrix or encapsulation with an inert shell, resulting in shape-stabilized PCMs that maintain their macroscopic shape during phase change. The synthesis and properties of Bi/ZnO nanocomposites were investigated in order to obtain shape-stabilized phase change materials. All samples consisted of metallic Bi and oxide, doped with 1–3% at. zinc. Heat storage capacities between 31 and 49 Jg−1 were obtained, depending on the mass fraction of the metal. All samples had good thermal reliability, retaining their heat storage properties after 50 consecutive heating–cooling cycles. An average oxide layer thickness of 75–100 nm is sufficient to prevent the molten metal leakage at temperatures above its melting point, resulting in shape-stabilized PCMs.
19 August 2018 in Journal of Thermal Analysis and Calorimetry