Debdeep Sarkar

Dr. Debdeep Sarkar

Ruhr University Bochum, Bochum, North Rhine-Westphalia, Germany
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 June 2020 in Soils and Foundations
Verified
Journal Article
Open access
Debdeep SarkarDebdeep Sarkar
Debdeep Sarkar
MGMeisam Goudarzy
Meisam Goudarzy
DKDiethard König
Diethard König
TWTorsten Wichtmann
Torsten Wichtmann

28 July 2021 in Acta Geotechnica
Verified
Journal Article
Open access
PDF file
Meisam GoudarzyMeisam Goudarzy
Meisam Goudarzy
Debdeep SarkarDebdeep Sarkar
Debdeep Sarkar
WLWolfgang Lieske
Wolfgang Lieske
TWTorsten Wichtmann
Torsten Wichtmann
The paper presents an experimental study on the effect of plastic fines content on the undrained behavior and liquefaction susceptibility of sand–fines mixtures under monotonic loading. The results of undrained monotonic triaxial compression tests conducted on mixtures of Hostun sand with varying amount (0–20%) and type (kaolin and calcigel bentonite) of plastic fines are presented. The specimens were prepared with different initial densities using the moist tamping method and consolidated at two different isotropic effective stresses. The results demonstrate that for both types of plastic fines, an increase in the fines content leads to a more contractive response and lower values of mobilized deviatoric stress. Despite similar relative density and fines content, the sand–kaolin mixtures showed a more contractive behavior than the sand–calcigel specimens. The steady-state lines (SSLs) ine–p´ space generally move downwards with increasing clay content. While the slopes of the SSLs for the clean Hostun sand and the mixtures with 10 and 20% kaolin are quite similar, the SSL lines for the specimens containing 10% or 20% calcigel run steeper or flatter, respectively. The inclination of the SSL in theq–p′ plane was found independent of clay type and content. The sand–kaolin mixtures were observed to be more susceptible to instability and flow liquefaction than the sand–calcigel mixtures.

1 October 2019 in Particuology
Verified
Journal Article
Closed access
Debdeep SarkarDebdeep Sarkar
Debdeep Sarkar
DKDiethard König
Diethard König
MGMeisam Goudarzy
Meisam Goudarzy

25 July 2022 in Acta Geotechnica
Verified
Journal Article
Open access
PDF file
Meisam GoudarzyMeisam Goudarzy
Meisam Goudarzy
Debdeep SarkarDebdeep Sarkar
Debdeep Sarkar
TWTorsten Wichtmann
Torsten Wichtmann
The paper presents an experimental study on the effect of plastic fines content on the undrained behavior and liquefaction susceptibility of sand-fines mixtures under cyclic loading. The results of undrained cyclic triaxial tests conducted on mixtures of Hostun sand with varying amounts (0–20%) and types (kaolin and calcigel bentonite) of plastic fines are presented. The specimens were prepared with different initial densities using the moist tamping method, consolidated at the same isotropic effective stress of 100 kPa and subjected to different deviatoric stress amplitudes. From the experimental observations, it was found that sand-clay mixtures with 10% or 20% clay content showed a lower cyclic liquefaction resistance than pure sand. Furthermore, the reduction in the cyclic stress ratio resulting in liquefaction after twenty cycles was found larger for sand-kaolin mixtures than for the sand-calcigel ones. Possible explanations are provided.

1 August 2024 in Géotechnique
Verified
Journal Article
Closed access
Debdeep SarkarDebdeep Sarkar
Debdeep Sarkar
MGMeisam Goudarzy
Meisam Goudarzy
TWTorsten Wichtmann
Torsten Wichtmann
The aim of the current study is to provide evidence regarding the influence of particle size on the dynamic properties in granular materials. Experiments using a resonant column (RC) device were conducted on glass beads having similar coefficient of uniformity, but four different mean grain sizes to describe the tendencies in the magnitude of Gmax and Emax. It can be clearly seen that for similar particle gradation the influence of particle size is significant, in particular for larger mean grain sizes d50 exceeding 1·5 mm. The experimental data were fitted using existing empirical relationships with corresponding fitting parameters. The fitting parameters describing the void ratio and pressure dependence to estimate maximum stiffness were found to depend on grain size to a certain extent. This influence was diminished for the materials with a d50 < 1·5 mm. It was therefore possible to use a unique set of fitting parameters for these materials with a satisfying degree of accuracy. The results were compared with some previous studies to highlight the size dependency of Gmax and Emax for materials with mean size greater than 2 mm, but also the relatively small influence on materials with lower mean particle sizes (d50 < 2 mm) is acknowledged. The results are furthermore discussed through a micromechanical interpretation highlighting why larger grain sizes influence stiffness values.