Debela A. TeKlemariyem

Mr. Debela A. TeKlemariyem

Mechanical Engineering and Robotics, AGH University of Science and Technology, Kraków, Małopolskie, Poland
orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 June 2024 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
MSMaisa A. Sharaf
Maisa A. Sharaf
SMSeifelislam A. Marzouk
Seifelislam A. Marzouk
AAAhmad Aljabr
Ahmad Aljabr
FAFahad Awjah Almehmadi
Fahad Awjah Almehmadi
TATabish Alam
Tabish Alam
Debela A. TeKlemariyemDebela A. TeKlemariyem
Debela A. TeKlemariyem

23 February 2024 in Heliyon
Verified
Journal Article
Open access
Debela A. TeKlemariyemDebela A. TeKlemariyem
Debela A. TeKlemariyem
EYEshetu Tadesse Ymer
Eshetu Tadesse Ymer
Venkata Ramayya AnchaVenkata Ramayya Ancha
Venkata Ramayya Ancha
BZBalewgize Amare Zeru
Balewgize Amare Zeru
This research examines the optimal 3D geometric parameters and shape of empty diffusers to enhance the mass flow rate of the HAWT rotor plane using a detailed parametric study. Previous works have investigated the use of diffusers to augment turbine power output; however, different curvature surfaces and the effects of all associated angles have not been considered for a thorough evaluation. This work mainly focuses on analyzing the effect of opening angles (2° to 22°), inlet shroud angles (8° to 24°), flange height ratios, flange angles (0° and 15°), and shape of the diffuser as well as flanges on velocity, pressure at the diffuser entry, and through the diffuser section at a wind speed of 4.5 m/s. At an inlet-shroud angle of 24° and an opening angle of 8°, with a diffuser flange height-throat diameter ratio of 0.3, the system achieved an 82.9% increase in flowrate. The diffuser with an inlet shroud-side lower stepped flange showed an optimum velocity of 9.12 m/s (maximum) and 8.2 m/s (average), resulting in a 102.66% and 82.2% increase in velocity, respectively. The percentage increase in velocity of the present study is 92.61%, compared with the previous maximum increase in rate of 53.8%, and then an increase in velocity of 38.81% was obtained. The optimum speed occurred at 0.175 m from the inlet section of the diffuser, indicating where the turbine should best be located. The CFD results from this work were validated with experimental data from the literature, showing a good agreement between the two. Integrated diffuser-turbine system simulation and experimental work with field tests are recommended as a way forward.

17 January 2024 in Heliyon
Verified
Journal Article
Open access
Geleta Afessa MoredaGeleta Afessa Moreda
Geleta Afessa Moreda
STSorome Deresa Tolasa
Sorome Deresa Tolasa
Debela A. TeKlemariyemDebela A. TeKlemariyem
Debela A. TeKlemariyem
Bioenergy is now recognized to be capable of providing the vast majority of predicted future renewable energy supply. Biomass is currently considered a common and commonly used renewable energy source. This study depends upon the investigation of khat waste using Aspen Plus software, which is required for creating environmentally friendly energy sources capable of improving our access to energy and economic sustainability. The outcome of the study is to understand the characteristics of the pyrolysis process without conducting a time-consuming, expensive, and complex procedure. The results of the investigation will be useful in determining the best feedstock for the formation of biofuel. Aspen Plus software simulates several ash-free organic components, including carbon, oxygen, nitrogen, hydrogen, and sulfur, with results like 45.72 % for carbon, 5.84 % for hydrogen, 0.43 % for nitrogen, and 38.56 % for oxygen. The production of biofuel is affected by processing parameters such as temperature and total mass flow rate. During reactions with the same mass but different temperatures, the bio-oil declined from 600 °C to 800 °C, while the maximum gas emission climbed quickly and the biochar reduced. In addition, it was recovered from Khat waste and proved to have an energy efficiency of 80.75 % and a net energy capacity of 134.25 kW. In addition, the High heating value (HHV) can be obtained from Khat waste is 19.38 MJ/kg, and low heating (LHV) can be 18.12 MJ/kg. We have been able to realize it using the Institute of Gas Technology formula based on ultimate analysis. The results show that Khat produces more oil than other wastes. As a result, all Khat waste is naturally occurring and Khat waste usually contains less nitrogen and no sulfur when used as fuel, which is an air pollutant reducing and protecting the environment.

29 August 2025 in Energies
Verified
Journal Article
Open access
PDF file
Debela A. TeKlemariyemDebela A. TeKlemariyem
Debela A. TeKlemariyem
NSNasir Hussain Razvi Syed
Nasir Hussain Razvi Syed
Phong B. DaoPhong B. Dao
Phong B. Dao
In the global shift toward sustainable energy, enhancing the efficiency of renewable energy systems plays a pivotal role in advancing the Sustainable Development Goals. This study focuses on optimizing the design of a corrugated-flange diffuser integrated with a wind turbine to enhance its performance, particularly in low-wind conditions. While most previous research has examined wind farm performance at high wind speeds, the challenge of effective power extraction at low wind speeds remains largely unresolved. The potential of diffusers to enhance wind turbine efficiency under low-wind conditions has received limited investigation, with most prior studies focusing solely on empty diffuser configurations without turbine integration. In addition, the influence of flange geometry on diffuser performance remains largely unexplored. In this study, parametric analyses were conducted to identify the optimal diffuser design, followed by comparative performance evaluations of configurations with and without turbine integration, using computational fluid dynamics (CFD) simulations. The results show that integrating a turbine with the optimized corrugated-flange diffuser increased flow velocity by 67.85%, achieving an average of approximately 14 m/s around the blade region. In comparison, the optimized corrugated-flange diffuser alone increased flow velocity by 44%, from 4.5 m/s to 8.036 m/s. These findings highlight the potential of optimized diffuser designs to enhance small-scale wind turbine performance in low-wind conditions.

10 October 2024 in Heliyon
Verified
Journal Article
Open access
Geleta Afessa MoredaGeleta Afessa Moreda
Geleta Afessa Moreda
Debela A. TeKlemariyemDebela A. TeKlemariyem
Debela A. TeKlemariyem
STSorome Deresa Tolasa
Sorome Deresa Tolasa
GGGamachis Ragasa Gutata
Gamachis Ragasa Gutata
This study explores the potential of Khat waste as a biofuel through a detailed analysis of its physical properties and pyrolytic behavior, employing both laboratory and simulation techniques. Biomass, including Khat waste, is a valuable renewable energy source with potential applications in reducing waste and CO2 emissions, especially in rural areas of developing countries like Ethiopia. The physical properties of the Khat waste were thoroughly examined, including moisture content, ash, volatile matter (VM), fixed carbon (FC), and elemental composition. The apparent density of the pyrolyzed khat waste was found to be 0.9688 g/cm³. The TGA results showed a moisture loss of 6.7 %, volatile matter of 4.7 %, fixed carbon of 6.78 %, and ash content of 5.55 %. Notably, Khat waste exhibited unique thermal behavior with a downward shift in TG curves above 220 °C. DTGA identified three decomposition peaks: moisture evaporation at 100 °C, hemicellulose breakdown at 210 °C, and cellulose degradation at higher temperatures. Fourier Transform Infrared Spectroscopy (FTIR) provided insights into the functional groups present in Khat waste, including alkene functional groups and O-H bonds, which are crucial for biofuel properties. Simulation using Aspen Plus software modeled the pyrolysis process, highlighting how varying heating rates affect volatile matter and fixed carbon content. Increasing heating rates decreased volatile matter and moisture but increased fixed carbon content. These findings offer valuable insights for optimizing Khat waste as a biofuel, emphasizing the need for tailored pyrolysis conditions to enhance biofuel production efficiency.

25 December 2025 in Energies
Verified
Journal Article
Open access
PDF file
AHAbu Al Hassan
Abu Al Hassan
NSNasir Hussain Razvi Syed
Nasir Hussain Razvi Syed
Debela A. TeKlemariyemDebela A. TeKlemariyem
Debela A. TeKlemariyem
Phong B. DaoPhong B. Dao
Phong B. Dao
Robust condition monitoring of wind turbine blades is essential for reducing downtime and maintenance costs, particularly under variable operating conditions. While recent studies suggest that combining trend monitoring (TM) with change point detection (CPD) can improve diagnostic performance, it remains unclear whether such integration is beneficial for all fault types. This study experimentally evaluates the integration of TM and CPD using vibration data from a laboratory-scale wind turbine for two representative blade faults: leading-edge erosion and twist misalignment. For the erosion case, discrete wavelet transform (DWT) energy features exhibit a clear and persistent increase in mid-frequency content, with energy deviations of approximately 34–45% relative to the healthy state. However, Bayesian Online Change Point Detection (BOCPD) does not reveal distinct change points, indicating that CPD provides limited additional value for gradual, steady-state degradation. In contrast, for twist misalignment, the short-time Fast Fourier Transform (FFT) features reveal dynamic spectral redistribution, and CPD applied to spectral centroid trends produces a sharp, localized detection signature. These results demonstrate that integrating TM with CPD significantly enhances fault detectability for dynamic, instability-driven faults, while TM alone is sufficient for smooth, steady-state degradation. This study provides an evidence-based guideline for selectively integrating CPD into wind turbine blade condition monitoring systems based on fault physics.