Depeng Shen

Dr. Depeng Shen

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 May 2020 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
DSDepeng Shen
Depeng Shen
NXN. Xu
N. Xu
MGM. Y. Gong
M. Y. Gong
PLP. Li
P. Li
HZH. B. Zhou
H. B. Zhou
GWGerhard Wilde
Gerhard Wilde

9 September 2024 in Materials
Verified
Journal Article
Open access
PDF file
YZYu Zhang
Yu Zhang
DSDepeng Shen
Depeng Shen
GLGuoqiang Liu
Guoqiang Liu
BTBingtao Tang
Bingtao Tang
This study examines the impact of high-pressure torsion (HPT) processing at various temperatures on the precipitation behavior of Cu-Cr alloys. The introduction of defects through HPT is observed to promote the precipitation of Cr atoms. Unlike the traditional large-scale precipitation that typically occurs around 400 °C, HPT can induce the precipitation of solute atoms even at room temperature. Furthermore, the temperature at which HPT is performed significantly influences the behavior of the precipitated phase during subsequent aging, ultimately affecting the alloy’s overall properties. At elevated temperatures (ETs) and room temperature (RT), Cr atoms tend to aggregate, forming Guinier–Preston (GP) zones or precipitates, which coarsen into incoherent precipitates after annealing. In contrast, when HPT is conducted at liquid nitrogen temperature (LNT), Cr atoms are retained in their original positions, leading to the formation of uniformly distributed, high-density small precipitates post-annealing. This phenomenon results in superior properties for HPT-LNT-treated samples, evidenced by a microhardness of 191.8 ± 3.2 HV and an electrical conductivity of 84.6 ± 1.8% IACS.

8 May 2026 in Materials
Verified
Journal Article
Open access
PDF file
YAYelong An
Yelong An
GLGuoqiang Liu
Guoqiang Liu
YZYu Zhang
Yu Zhang
BTBingtao Tang
Bingtao Tang
YZYong Zhao
Yong Zhao
DSDepeng Shen
Depeng Shen
A systematic investigation was conducted on the effects of Cr alloying on the tensile behavior and microstructural evolution of TiZrNb medium-entropy alloys at 673 K. For comparison, the influences of Al and Cu alloying on the mechanical properties of TiZrNb were also examined. Although Al and Cu alloying enhanced the ultimate tensile strength at room temperature, their improvements in strength and ductility at 673 K were limited. In contrast, the TiZrNb98.5Cr1.5 alloy retained a single body-centered cubic (BCC) phase without forming the conventionally expected Laves phase. Cr effectively suppressed the formation of Zr-rich precipitates. At a strain rate of 1.67 × 10−3 s−1 and 673 K, TiZrNb98.5Cr1.5 exhibits an increase in the ultimate tensile strength of approximately 408 MPa compared with the base TiZrNb alloy, while the fracture elongation increases from 10% to 25% and the threshold stress rises from 669 MPa to 1196 MPa, achieving a markedly improved strength–ductility synergy. These results indicate that Cr alloying effectively stabilizes the microstructure and enhances the mechanical performance of TiZrNb alloys at 673 K by suppressing precipitate formation and reducing dislocation accumulation, outperforming Al and Cu alloying at the same temperature.

3 June 2024 in Materials
Verified
Journal Article
Open access
PDF file
CDCunchao Dou
Cunchao Dou
ZSZhendong Sun
Zhendong Sun
DSDepeng Shen
Depeng Shen
NGNing Guo
Ning Guo
ZLZhe Liu
Zhe Liu
BTBingtao Tang
Bingtao Tang
The Laasraoui segmented and Arrhenius flow stress model, dynamic recrystallization (DRX) model, grain size prediction model, and hot processing map (HPM) of Fe-Cr-Mo-Mn steels were established through isothermal compression tests. The models and HPM were proven by experiment to be highly accurate. As the deformation temperature decreased or the strain rate increased, the flow stress increased and the grain size of the Fe-Cr-Mo-Mn steel decreased, while the volume fraction of DRX (Xdrx) decreased. The optimal range of the hot processing was determined to be 1050–1200 °C/0.369–1 s−1. Zigzag-like grain boundaries (GBs) and intergranular cracks were found in the unstable region, in which the disordered martensitic structure was observed. The orderly packet martensite was formed in the general processing region, and the mixed structure with incomplete DRX grains was composed of coarse and fine grains. The microstructure in the optimum processing region was composed of DRX grains and the multistage martensite. The validity of the Laasraoui segmented flow stress model, DRX model, grain size prediction model, and HPM was verified by upsetting tests.

1 February 2025 in Vacuum
Verified
Journal Article
Closed access
HZHongbo Zhou
Hongbo Zhou
HJHaihong Jiang
Haihong Jiang
LYLi Yu
Li Yu
GDGan Ding
Gan Ding
SCSonglin Cai
Songlin Cai
GWGerhard Wilde
Gerhard Wilde

19 April 2026 in Journal of Materials Science
Verified
Journal Article
Closed access
YSYuanmao Shi
Yuanmao Shi
DSDepeng Shen
Depeng Shen
FWFangxing Wu
Fangxing Wu
YZYu Zhang
Yu Zhang
XPXiaoning Pei
Xiaoning Pei
GLGuoqiang Liu
Guoqiang Liu