Hot stamping components with tailored mechanical properties have excellent safety-related performance in the field of lightweight manufacturing. In this paper, the constitutive relation and damage evolution of bainite, martensite, and mixed bainite/martensite (B/M) phase were studied. Two-dimensional representative volume element (RVE) models were constructed according to microstructure characteristics. The constitutive relations of individual phases were defined based on the dislocation strengthening theory. Results showed that the damage initiation and evolution of martensite and bainite phases can well described by the Lou-Huh damage criterion (DF2015) determined by the hybrid experimental–numerical method. The calibrated damage parameters of each phase were applied to the numerical simulation, followed by the 2D RVE simulations of B/M phase under different stress states. To study the influence of martensite volume fraction (Vm) and distribution of damage evolution, the void nucleation and growth were evaluated by RVEs and verified by scanning electron microscope (SEM). Three types of void nucleation modes under different stress states were experimentally and numerically studied. The results showed that with the increase of Vm and varying martensite distribution, the nucleation location of voids move from bainite to martensite.
This study examines the impact of high-pressure torsion (HPT) processing at various temperatures on the precipitation behavior of Cu-Cr alloys. The introduction of defects through HPT is observed to promote the precipitation of Cr atoms. Unlike the traditional large-scale precipitation that typically occurs around 400 °C, HPT can induce the precipitation of solute atoms even at room temperature. Furthermore, the temperature at which HPT is performed significantly influences the behavior of the precipitated phase during subsequent aging, ultimately affecting the alloy’s overall properties. At elevated temperatures (ETs) and room temperature (RT), Cr atoms tend to aggregate, forming Guinier–Preston (GP) zones or precipitates, which coarsen into incoherent precipitates after annealing. In contrast, when HPT is conducted at liquid nitrogen temperature (LNT), Cr atoms are retained in their original positions, leading to the formation of uniformly distributed, high-density small precipitates post-annealing. This phenomenon results in superior properties for HPT-LNT-treated samples, evidenced by a microhardness of 191.8 ± 3.2 HV and an electrical conductivity of 84.6 ± 1.8% IACS.
A systematic investigation was conducted on the effects of Cr alloying on the tensile behavior and microstructural evolution of TiZrNb medium-entropy alloys at 673 K. For comparison, the influences of Al and Cu alloying on the mechanical properties of TiZrNb were also examined. Although Al and Cu alloying enhanced the ultimate tensile strength at room temperature, their improvements in strength and ductility at 673 K were limited. In contrast, the TiZrNb98.5Cr1.5 alloy retained a single body-centered cubic (BCC) phase without forming the conventionally expected Laves phase. Cr effectively suppressed the formation of Zr-rich precipitates. At a strain rate of 1.67 × 10−3 s−1 and 673 K, TiZrNb98.5Cr1.5 exhibits an increase in the ultimate tensile strength of approximately 408 MPa compared with the base TiZrNb alloy, while the fracture elongation increases from 10% to 25% and the threshold stress rises from 669 MPa to 1196 MPa, achieving a markedly improved strength–ductility synergy. These results indicate that Cr alloying effectively stabilizes the microstructure and enhances the mechanical performance of TiZrNb alloys at 673 K by suppressing precipitate formation and reducing dislocation accumulation, outperforming Al and Cu alloying at the same temperature.
Quenching and partitioning (QP) steel has attracted much focus due to the effect of phase transformation induced plasticity (TRIP). However, the TRIP behavior makes it difficult to accurately predict the strain and stress distribution as well as the phase transformation behavior of QP steel. Scanning electron microscope (SEM) images of the QP980 microstructure were produced in this study, characterized by a combination of lath martensite, polygonal ferrite and retained austenite. The volume fraction evolution of retained austenite with equivalent plastic strain (EPS) of uniaxial tension was obtained by electron-backscatter diffraction. The phase transformation kinetics equations of QP980 were deduced based on the phase transformation model proposed by Olson and Cohen (simplified as O-C theory), considering the effects of strain rate, deformation temperature and stress state. A constitutive model on the dependence of the phase transformation was proposed to reveal the relation between metallographic characteristics and mechanical performance of QP980 steel during deformation. The User subroutine VUMAT in ABAQUS/Explicit was implemented to describe the volume fraction of retained austenite (VFRA) under different stress states. The established phase transformation and constitutive model were applied to three kinds of complex path loading tests. The variation in the retained austenite under complex strain paths was obtained and compared with the experimental results.
19 October 2025 in Metallurgical and Materials Transactions A