Supercritical operation is considered a main technique to achieve higher cycle efficiency in various thermodynamic systems. The present paper is a review of experimental investigations on supercritical operation considering both heat-to-upgraded heat and heat-to-power systems. Experimental works are reported and subsequently analyzed. Main findings can be summarized as: steam Rankine cycles does not show much studies in the literature, transcritical organic Rankine cycles are intensely investigated and few plants are already online, carbon dioxide is considered as a promising fluid for closed Brayton and Rankine cycles but its unique properties call for a new thinking in designing cycle components. Transcritical heat pumps are extensively used in domestic and industrial applications, but supercritical heat pumps with a working fluid other than CO2 are scarce. To increase the adoption rate of supercritical thermodynamic systems further research is needed on the heat transfer behavior and the optimal design of compressors and expanders with special attention to the mechanical integrity.
Low-enthalpy geothermal resources (<150 °C) can be used for electricity generation and are widespread around the world, occurring at shallow depths. At the same time, in many parts of the world, there are existing low-enthalpy geothermal wells that are used for a multitude of applications such as for buildings’ heating and agriculture-related applications. The dominant technology to convert low-grade heat (<150 °C) to electricity is the Organic Rankine Cycle (ORC). The autonomous polygeneration microgrid (APM) concept aims to holistically meet in a sustainable way the needs of an off-grid community in terms of electrical loads, space heating and cooling, potable water production through desalination, and the use of hydrogen as fuel for transportation, in the most cost-effective manner possible. Photovoltaics (PVs) and wind turbines have been investigated extensively, since PVs can be installed practically anywhere in the world and wind turbines in areas with sufficient wind potential. The aim of this paper is to investigate techno-economically the potential of utilizing low-enthalpy geothermal resources in small-scale APMs through an ORC engine to fully satisfy the needs of small settlements. In order to accomplish this task with confidence, a case study for the Greek island of Milos has been developed and a typical settlement has been considered. It is worth mentioning that experimental results from a realized low-power (<10 kWe) ORC engine manufactured to operate at temperatures up to 140 °C are used to add reliability in the calculations. In order to meet the needs of the people, four different APMs based on PVs, wind turbines, and geothermal ORC of different but appropriate configurations were designed and sized through optimization. The optimization process was based on particle swarm optimization (PSO). The comparative examination of the results shows that the use of a low-power, low-temperature ORC engine in an APM is technically feasible; more cost effective than the configurations based on PVs, wind turbines, or combination of both; and has increased environmental sustainability.
The brine produced from desalination systems is a highly concentrated mixture, including cleansing chemicals from the water treatment processes that can possibly degrade ecosystems in discharge areas. Evaporation is a widely used method for the treatment of high salinity mixtures; however, it requires careful monitoring of the temperature and pressure in order to protect the equipment from the highly corrosive environment of the brine discharge. The proposed brine treatment system is based on the principle of vacuum evaporation with the use of a high-temperature heat pump, which is classified as “green technology”. In this study, a thermodynamic analysis of a vacuum evaporation system with a nominal freshwater production capacity of 160 L/h has been carried out, employing a numerical tool to model the flash evaporator and the heat pump. The analysis focuses on the parameters that present the most significant impact on the system’s efficiency and water production, such as the recirculation ratio, the set-point temperature of the heat pump and the pressure difference provided by the vacuum pump. The results show that, for the constant vacuum pressure difference, the water production increases with the increase in the set-point temperature and the recirculation ratio, but leads to the reduced COP of the heat pump and to an elevated specific energy consumption. Moreover, it is shown that an increased vacuum pressure difference leads to increased water production, but reduces the COP. Finally, the minimum specific energy consumption of 150 kWh/m3 of produced freshwater can be achieved for a set-point at 75 °C and vacuum of 0.21 bar, leading to a levelized cost of water about 11 €/m3.