Hayrettin AHLATCI

Mr. Hayrettin AHLATCI

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2019 in Coatings
Verified
Journal Article
Open access
PDF file
YOYasin Ozgurluk
Yasin Ozgurluk
MDMert Doleker
Mert Doleker
DODervis Ozkan
Dervis Ozkan
HAHayrettin AHLATCI
Hayrettin AHLATCI
AKAbdullah Cahit Karaoglanli
Abdullah Cahit Karaoglanli
The cold gas dynamic spray (CGDS) method has been considered a promising technology to produce a metallic bond coat for thermal barrier coating (TBC) systems. In this study, CoNiCrAlY bond coats produced by CGDS method were coated with yttria-stabilized zirconia (YSZ) by electron beam physical vapor deposition (EB-PVD). TBCs were subjected to 50 wt % V2O5 and 50 wt % Na2SO4 molten hot corrosion salt combinations at 1000 °C. In the case of YSZ top coat on TBCs, the reaction between Na2SO4, V2O5, and Y2O3 salts generates YVO4 crystals, and these structures cause the transformation of tetragonal ZrO2 to monoclinic ZrO2. This situation occurs under operating conditions that lead to TBC failure. Hot corrosion behavior and the related failure mechanisms of TBC systems were investigated and discussed using scanning electron microscope (SEM), energy dispersive spectroscopy (EDS) analysis, and X-ray diffractometer (XRD).


1 September 2019 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
YSYasin Subasi
Yasin Subasi
YTYunus Turen
Yunus Turen
HZHuseyin Zengin
Huseyin Zengin
HAHayrettin AHLATCI
Hayrettin AHLATCI
YSYavuz Sun
Yavuz Sun

19 June 2019 in Materials Research Express
Verified
Journal Article
Closed access
PDF file
LELevent Elen
Levent Elen
BCBunyamin Cicek
Bunyamin Cicek
EKErkan Koc
Erkan Koc
YTYunus TUREN4
Yunus TUREN4
YSYavuz Sun
Yavuz Sun
HAHayrettin AHLATCI
Hayrettin AHLATCI
Magnesium and its alloys have become important structural materials in the last couple of decades due to their exceptional and mechanical properties. In this study, the effects of the introduction Cd, Bi, and Sn alloying elements were introduced into AM60 alloys produced from Mg-Al-Mn triple junction in order to improve the microstructural and mechanical properties. The weight percent of the alloying elements was chosen as 0.5% wt. besides the introduction of the additional alloying elements, the effect of cooling rate on microstructural and mechanical properties of the alloys have been investigated. The results showed that the alloying elements introduced to AM60 resulted in an improvement in the mechanical properties of the alloys, which is attributed to the changes in the microstructure. The higher cooling rate led to the formation of the finer α-Mg master matrix which in turn enhanced the mechanical properties of the alloys. It was observed that the intermetallic phase of β-Mg17Al12 at the grain boundaries became thinner due to the rapid cooling rate and the introduction of the alloying elements, and the continuity decreased and the intergranular distance shortened. The addition of the alloying element increased the tensile strength of the AM60 alloy from 140 MPa to 210 MPa and the elongation values increased from 5% to 22%. The effects of the alloying elements and the cooling rate on the hardness and yields properties of the samples were also studied.

25 May 2023 in Materials
Verified
Journal Article
Open access
PDF file
ASAboujaila A. M. Soltan
Aboujaila A. M. Soltan
İEİsmail Esen
İsmail Esen
SKSeyit Ali KARA
Seyit Ali KARA
HAHayrettin AHLATCI
Hayrettin AHLATCI
In this study, corrosion and wear tests of NiTi alloy (Ni 55%–Ti 45%) samples, known as shape memory alloy, which offer a shape recovery memory effect between memory temperatures ranging from 25 to 35 °C, have been carried out. The standard metallographically prepared samples’ microstructure images were obtained using an optical microscope device and SEM with an EDS analyzer. For the corrosion test, the samples are immersed with a net into the beaker of synthetic body fluid, whose contact with the standard air is cut off. Electrochemical corrosion analyses were performed after potentiodynamic testing in synthetic body fluid and at room temperature. The wear tests of the investigated NiTi superalloy were carried out by performing reciprocal wear tests under 20 N and 40 N loads in a dry environment and body fluid. During wear, a 100CR6-quality steel ball of the counter material was rubbed on the sample surface for a total of 300 m with a unit line length of 13 mm and a sliding speed of 0.04 m/s. As a result of both the potentiodynamic polarization and immersion corrosion tests in the body fluid, an average of 50% thickness reduction in the samples was observed in proportion to the change in the corrosion current values. In addition, the weight loss of the samples in corrosive wear is 20% less than that in dry wear. This can be attributed to the protective effect of the oxide film on the surface at high loads and the effect of reducing the friction coefficient of the body fluid.

21 July 2023 in Materials
Verified
Journal Article
Open access
PDF file
MAMohamed Ali Ibrahim Alwakwak
Mohamed Ali Ibrahim Alwakwak
İEİsmail Esen
İsmail Esen
HAHayrettin AHLATCI
Hayrettin AHLATCI
EKEsma Keskin
Esma Keskin
In this study, the microstructural properties and corrosion behavior of RE elements (Y, La) added to magnesium in varying minors after casting and homogenization heat treatment were investigated. Three-phase structures, such as α-Mg, lamellae-like phases, and network-shaped eutectic compounds, were seen in the microstructure results. The dendrite-like phases were evenly distributed from the eutectic compounds to the interior of the α-Mg grains, while the eutectic compounds (α-Mg + Mg) RE (La/Y)) were distributed at the grain boundaries. According to the corrosion results, the typical hydroxide formation for lanthanum content caused the formation of crater structures in the material, and with the increase in lanthanum content, these crater structures increased both in depth and in density. In addition, the corrosion products formed by Y2O3 and Y(OH)3 in the Mg-3.21Y-3.15 La alloy increased the thickness of the corrosion film and formed a barrier that protects the material against corrosion. The thinness of the protective barrier against corrosion in the Mg-4.71 Y-3.98 La alloy is due to the increased lanthanum and yttrium ratios. In addition, the corrosion resistance of both Mg-3.21Y-3.15 La and Mg-4.71 Y-3.98 La alloys decreases after homogenization. This negative effect on corrosion is due to the coaxial distribution of oxide/hydroxide layers formed by yttrium and lanthanum after homogenization.