Metallic glasses (MGs) are a type of multicomponent non-crystalline metallic alloys obtained by rapid cooling, which possess several physical, mechanical, and chemical advantages against their crystalline counterparts. In this work, an Fe-based MG is explored as a hydrogen storage material, especially, due to the evidence in previous studies about the capability of some amorphous metals to store hydrogen. The evaluation of an Fe-based MG as a novel negative electrode material for nickel/metal hydride (Ni-MH) batteries was carried out through cyclic voltammetry and galvanostatic charge–discharge tests. A conventional LaNi5 electrode was also evaluated for comparative purposes. The electrochemical results obtained by cyclic voltammetry showed the formation of three peaks, which are associated with the formation of Fe oxides/oxyhydroxides and hydroxides. Cycling charge/discharge tests revealed activation of the MG electrode. The highest discharge capacity value was 173.88 mAh/g, but a decay in its capacity was observed after 25 cycles, contrary to the LaNi5, which presents an increment of the discharge capacity for all the current density values evaluated, reached its value maximum at 183 mAh/g. Characterization analyses performed by X-ray diffraction, Scanning Electron Microscopy and Raman Spectroscopy revealed the presence of corrosion products and porosity on the surface of the Fe-based MG electrodes. Overall, the Fe-based MG composition is potentially able to work as a negative electrode material, but degradation and little information about storage mechanisms means that it requires further investigation.
This study presents the design and implementation of different types of manifolds (sampling system) to measure water flow properties (velocity, pressure, and temperature) through the high- and low-pressure section of a Francis-type low head hydraulic turbine (LHT of 52 m) to calculate it is efficiency using the Thermodynamic Method (TM). The design of the proposed manifolds meets the criteria established in the “International Electrotechnical Commission—60041” Standard for the application of the TM in the turbine. The design of manifolds was coupled to the turbine and tested by the Computational Fluid Dynamics (CFD) application, under the same experimental conditions that were carried out in a power plant, without the need for on-site measurements. CFD analyses were performed at different operating conditions of volumetric flow (between values of 89.67 m3/s and 35.68 m3/s) at the inlet of turbine. The mechanical power obtained and the efficiency calculated from the numerical simulations were compared with the experimental measurements by employing the Gibson Method (GM) on the same LTH. The design and testing of manifolds for high- and low-pressure sections in a low head turbine allows for the constant calculation of efficiency, avoiding breaks in the generation of electrical energy, as opposed to other methods, for example, the GM. However, the simulated (TM) and experimental (GM) efficiency curves are similar; therefore, it is proposed that the design of the manifolds is applied in different geometries of low-head turbines.
The drying kinetics and physical and chemical characteristics of Leucaena esculenta seed drying using a forced convection solar dryer are described. The drying kinetics behavior is examined for three experiments under climate conditions of three different winter days in central Mexico, observing significant effects related to the reported pH levels of the seeds with values of 6.34, 5.98, 5.97, 5.82, and 6.07. The airflow measurements inside the drying chamber were observed, including the geometric dimensions, color, appearance, weight, and moisture loss, and the effective diffusivity coefficient of Leucaena esculenta with values between 1.23 × 10−7 and 8.09 × 10−9 . Solar drying, with the technology used in this study, is a viable alternative to give added value to Leucaena esculenta. This study can be the basis for developing alternatives to preserve seeds for animal and human consumption.
No es ningún secreto que en el mundo existen amenazas que pueden acabar con la humanidad por completo: el calentamiento global es una de ellas. El dióxido de carbono (co2) es el gas de efecto invernadero que más contribuye a este problema. El proceso de generación de electricidad a partir de combustibles fósiles es la principal fuente de emisiones de co2 en México. A continuación se presenta una alternativa tecnológica para mitigar las emisiones de co2 provenientes de las centrales termoeléctricas de México con base en los datos reportados en inventarios de emisiones de gases y compuestos e informes anuales sobre centrales eléctricas, así como del registro de fuentes renovables en 2021.