The aim of this study was to evaluate the effect of biologically oriented preparation technique on the stress concentration of endodontically treated upper central incisors restored with zirconia crown (yttria-stabilized zirconia polycrystalline ceramic) through finite element analysis (FEA). Four models of maxillary central incisors containing enamel, dentin, periodontal ligament, cortical and medullary bone were created in CAD. Each model received a polymeric core-build up with nanofilled dental resin composite. The evaluated models were SM—preparation in shoulder 90°; CM—chamfer preparation; BOPT—biologically oriented preparation technique and BOPTB—BOPT preparation 1 mm below the cement-enamel junction. All models received zirconia crowns (5Y-TZP), fiberglass post and 1 mm ferrule. The models were imported into the analysis software with parameters for mechanical structural testing using the maximum principal stress and the tensile strength as the analysis criteria. Then, load of 150 N was applied at the cingulum with 45° slope to the long axis of the tooth, with the fixed base for each model. The type of marginal preparation affected the stresses concentration in endodontically treated teeth and in the zirconia crown margin. Considering the stress magnitude only, BOPT is a viable option for anterior monolithic zirconia crowns; however, with the highest stress magnitude at the restoration margin.
Dental implant-supported prosthesis are widely used in oral reconstruction of totally edentulous patients. Nonetheless, one of the most common failures in these cases is caused by overloading from improper occlusion. The aim of this work was to determine if the occlusal scheme influences the biomechanical response in implant-supported dental prostheses. Searches were conduct is several databases (PubMed/MEDLINE, The Cochrane Library, Web of Science, Scopus, LILACS, and Opengrey). We found 632 publications and 521 studies remained after removing duplicates. After applying the inclusion criteria, five studies were used in this systematic review: one clinical trial, one retrospective clinical trial, one in vitro and two in silico. The results show the lack of clinical and laboratory studies about occlusion in implant-supported prostheses. Although there are several studies regarding implant occlusion schemes, there remains a lack of scientific evidence to support that one specific occlusal scheme is superior to another, or to help define the ideal occlusal scheme that improves the clinical outcome. It can be concluded, however, that the proper distribution of loads and the absence of occlusal interferences can increase implant longevity. Thus, more clinical and laboratory studies must be carried out to obtain an occlusal scheme that favors the clinical success of implant rehabilitation.
Objective: Evaluate the effect of four preparation designs, two ceramic materials, and two occlusion contact types on the stress distribution of ceramic veneer in upper central incisor. Material and methods: 3D-models were performed in the modeling software containing enamel, dentin, pulp, periodontal ligament and a base of polyurethane resin. The designs were modeled and exported to the computer aided engineering software to perform the static structural analysis. For the mesh, a total of 155429 tetrahedron elements and 271683 nodes were used, after a 10% convergence test. Two materials, lithium disilicate and feldspathic ceramics, were simulated. A static load of 100 N on 45º was applied on the incisal and middle thirds of the palatal tooth region, guided by the occlusal plane. The base was constrained in all directions. The Maximum Principal Stress was the failure criteria chosen for the analysis. Results: The Finite Element Analysis showed that the most conservative designs presented less stress concentration on the ceramic veneer. However, the highest tensile stress concentrations were observed on lithium disilicate veneer with extend design, on the middle third. The type of occlusal contact presented different stress patterns among the preparation designs; the incisal contact showed higher stress concentration compared to middle third contact regardless the ceramic material. Conclusions: To perform a ceramic veneer in upper central incisor, the feldspathic ceramic presented promising results and should be recommended when the extended design was done. Regarding contact types, the incisal contact is more prone to failure regardless the ceramic and preparation design. Keywords Ceramics; Dental veneers; Finite element analysis.
1 January 2018 in Journal of Dentistry And Oral Implants
Currently, patients seeking dental treatment are increasingly concerned with the esthetics. Accordingly, the professional must be able to indicate treatment approaches that often include more than one specialty. This concept of integrated dentistry allows achieving excellence in results, which may not be reached one single Dentistry specialty. In addition, the multidisciplinary dentistry enables the solution of cases more conservatively, especially cases where aesthetics is a relevant factor. This study aimed to report a clinical case showing esthetic disharmony of the anterior teeth even after the ending of the orthodontic treatment, causing dissatisfaction for both the patient and the dentist. From a functional point of view, the occlusion was adequate. However, the esthetics prevented a satisfactory outcome. To solve this issue, the case was treated through minimally-invasive ceramic laminates, then reaching the expected result.
About Me
Phd student at Institute of Science and Technology of Sao Jose dos Campos (ICT-UNESP)O
Phd student at Institute of Science and Technology of Sao Jose dos Campos (ICT-UNESP)O