Although grinding kinetics has been the subject of many researches, there is no research examining the shape kinetics of particles ground by different mills using dynamic image analysis (DIA) in the literature. In this investigation, how the shapes of quartz particles change over time at two different size fractions in two different mills is modeled using the latest image analysis technique, since particle shape of mineral is important in flotation and hydraulic fracturing processes. Empirical time-dependent shape models based on the correlation between average circularity (Cav.) and bounding rectangle aspect ratio (BRARav.) parameters and grinding time for vibratory disc mill and ball milled particles are established with high R2 values by different fitting. Furthermore, average shape values of particles ground by the mills depending on grinding time were predicted for two size fractions. It was found that, Cav. data can be better described by linear fitting equations, on the other hand BRARav. data can be better represented by power fitting equations. Since predicted and measured shape values were found close to each other, this approach provides useful information for estimating the milling time required to produce the particles by milling (with less energy and cost) appropriately for intended use.
Since the particle size, shape, specific surface area, and purity of the ground calcium carbonate (GCC) decide its usability in the paper, paint, and plastic industries, the effect of grinding is important. However, the effect of stirred and ball mill grinding on the particle shape of GCC by dynamic image analysis (DIA) is still lacking in the literature. Therefore, the aim of this study is to compare the aspect ratio at the same fineness (d97 = 50 μm) and evaluate other properties such as color, and surface area of GCC particles by stirred and ball mill grindings. DIA results showed that particles produced by the ball mill had higher aspect ratio values than those by the stirred mill. This was attributed to the impact, and attrition breakage modes produced by the ball and stirred mill, respectively. This conclusion is supported by XRD and SEM. Finally, the results related to physical properties such as aspect ratio, surface area, and whiteness are discussed depending on the usage area of GCC.
Graphite, which is a key anode material for LIB, needs to have a high tap density (dt) to reach a high volumetric energy density. Since dt is directly correlated with particle size, particle size distribution, and particle shape, it can usually be improved by optimized grinding. So, determining the ideal grinding time by modeling the change in dt over grinding time can yield substantial benefits like time, energy, and economy. However, the grinding time-dependent dt modeling of graphite has never been reported before. Therefore, in this study, the relationship between the measured dt values and grinding times of graphite particles by a vibrating disc mill (VDM) was investigated. Then, the empirical time-dependent dt models were established with high R2 values. The experimental and predicted dt values were found to be close to each other. Among all tested fitting models, the exponential model (dt = ae−bt) was found to be the best-fitting model, having the highest R2 and lowest error values. This approach provides guidance in the powder flow and processing of ground mineral materials, in the preparation processes of high-density graphite LIB anode material, as well as in graphite grinding in other mills in the industry, as well as in different electrode materials.
24 December 2025 in Yüzüncü Yıl Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Bu çalışmada, Sivas Cumhuriyet Üniversitesi Maden Mühendisliği Bölümü Cevher Hazırlama Laboratuvarı’nda hematit, barit ve linyit numunelerinin boyut küçültme, öğütme ve zenginleştirme sırasında açığa çıkan partikül madde salınımları (PM) (TAPM, PM10, PM2.5 ve PM1) ayrıntılı biçimde araştırılmıştır. PM salınımları numune ve ekipman tipine bağlı olarak değişmektedir. Özellikle boyut küçültme ekipmanları (çekiçli kırıcı) ve değirmen gibi yüksek mekanik enerjiye sahip cihazlar en yüksek PM seviyelerini üretirken; sallantılı masa sistemi akışkan bir ortamda (su) ve besleme pülp şeklinde olduğu için en düşük PM salınımlarını göstermiştir. İstatistiksel analizlerde, ölçüm verilerinin geniş saçınımlı ve heterojen bir dağılıma sahip olduğunu ortaya koymuş; bu nedenle eşdeğer sürekli konsantrasyon değeri (Leq(PM)) yerine, aritmetik ortalama ve dağılım karakteristiklerini yansıtan histogramlar kullanılarak değerlendirmeler yapılmıştır. Sonuç olarak, cevher hazırlama süreçlerinin PM üretim potansiyeli bakımından ciddi riskler içerdiği, bu nedenle ekipman yerleşiminin optimize edilmesi ve işlem sıralamasının uygun şekonsantrasyon değeri (Leq(PM)) yerine, aritmetik ortalama ve dağılım karakteristiklerini yansıtan histogramlar kullanılarak değerlendirmeler yapılmıştır. Sonuç olarak, cevher hazırlama süreçlerinin PM üretim potansiyeli bakımından ciddi riskler içerdiği, bu nedenle ekipman yerleşiminin optimize edilmesi ve işlem sıralamasının uygun şekilde planlanması, daha güvenli ve sağlıklı bir çalışma ortamı oluşturulmasına doğrudan katkı sunacaktır.
Although particle shape plays a paramount role as much as particle size in the micronization and flotation stages used in the production of graphite material as LIB anode material, the relationship between graphite grinding and particle shape is almost non-existent. Therefore, this study aims to compare the particle shape of graphite particles at various grinding times with "tumbling" and "non-tumbling" mills, such as the most used laboratory ball mill and vibrating disc mill, by using DIA. According to both DIA and XRD, SEM, and stereo microscope results, VDM produced rounder particles in a shorter time than BM.