Muhammad Tahir

Dr. Muhammad Tahir

Agricultural Engineering Institute, NARC, Pakistan Agricultural Research Council, Islamabad, Islāmābād, Pakistan
orcid
Scientific Officer (Scientist/ Researcher)

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 February 2021 in Energies
Verified
Journal Article
Open access
PDF file
Hadeed AshrafHadeed Ashraf
Hadeed Ashraf
Muhammad SultanMuhammad Sultan
Muhammad Sultan
Redmond R. ShamshiriRedmond R. Shamshiri
Redmond R. Shamshiri
FAFarrukh Abbas
Farrukh Abbas
Muhammad FarhanMuhammad Farhan
Muhammad Farhan
Badar Munir Khan NiaziBadar Munir Khan Niazi
Badar Munir Khan Niazi
This study provides insights into the feasibility of a desiccant dehumidification-based Maisotsenko cycle evaporative cooling (M-DAC) system for greenhouse air-conditioning application. Conventional cooling techniques include direct evaporative cooling, refrigeration systems, and passive/active ventilation. which are commonly used in Pakistan; however, they are either not feasible due to their energy cost, or they cannot efficiently provide an optimum microclimate depending on the regions, the growing seasons, and the crop being cultivated. The M-DAC system was therefore proposed and evaluated as an alternative solution for air conditioning to achieve optimum levels of vapor pressure deficit (VPD) for greenhouse crop production. The objective of this study was to investigate the thermodynamic performance of the proposed system from the viewpoints of the temperature gradient, relative humidity level, VPD, and dehumidification gradient. Results showed that the standalone desiccant air-conditioning (DAC) system created maximum dehumidification gradient (i.e., 16.8 g/kg) and maximum temperature gradient (i.e., 8.4 °C) at 24.3 g/kg and 38.6 °C ambient air conditions, respectively. The DAC coupled with a heat exchanger (DAC+HX) created a temperature gradient nearly equal to ambient air conditions, which is not in the optimal range for greenhouse growing conditions. Analysis of the M-DAC system showed that a maximum air temperature gradient, i.e., 21.9 °C at 39.2 °C ambient air condition, can be achieved, and is considered optimal for most greenhouse crops. Results were validated with two microclimate models (OptDeg and Cft) by taking into account the optimality of VPD at different growth stages of tomato plants. This study suggests that the M-DAC system is a feasible method to be considered as an efficient solution for greenhouse air-conditioning under the climate conditions of Multan (Pakistan).

1 December 2019 in Biosystems Engineering
Verified
Journal Article
Closed access
Muhammad TahirMuhammad Tahir
Muhammad Tahir
JZJumin Zhang
Jumin Zhang
JXJunfang Xia
Junfang Xia
CZChunling Zhang
Chunling Zhang
HZHua Zhou
Hua Zhou
YZYinghao Zhu
Yinghao Zhu

17 January 2021 in Agronomy
Verified
Journal Article
Open access
PDF file
Muhammad TahirMuhammad Tahir
Muhammad Tahir
JZJumin Zhang
Jumin Zhang
JXJunfang Xia
Junfang Xia
YZYong Zhou
Yong Zhou
HZHua Zhou
Hua Zhou
HMHafiza Mamona
Hafiza Mamona
Farm tractors in cultivation consume a big amount of fossil fuels and emit greenhouse gases to the atmosphere. Improving traction performance and power transfer indices of wheeled tractors and field terrain soil with higher traction (pull ability) at optimal travel reduction (TR) can optimize energy utilization. This study compares the traction performance, fuel consumption, and field productivity, of a farm tractor equipped with a new drive wheel “rigid lugged wheel (RLW)” and conventional tire wheel (CTW) in field tillage operations. Tractor with RLW resulted 24.6 kN drawbar pull and 6.6 km.h−1 travel speed at 80% tractive efficiency and 15.6% TR. While with CTW, the drawbar pull and the travel speed were 23.2 kN and 6.0 km h−1 respectively at 68% tractive efficiency and 36.3% TR. The RLW resulted in improved traction performance with similar equipment weight. Tractor with RLW also resulted 220.5% lower TR, 14.8% higher field productivity, and 15.4% lower fuel consumption. RLW can control equipment weight and field traffic intensity with the improved traction performance of wheeled tractors and will make the field operations more energy-efficient and economical. For enhanced field drivability of RLW, further work is required to test for diverse field conditions and differently sized tractors.

8 July 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
KAkhaled ali
khaled ali
WZWangyuan Zong
Wangyuan Zong
Muhammad TahirMuhammad Tahir
Muhammad Tahir
LMLina Ma
Lina Ma
LYliu yang
liu yang
Sunflower threshing is one of the most interesting field processes for making the sunflower ready for seed handling, drying, cleaning and oil extraction. One of the biggest problems observed during the sunflower threshing process is the accumulation of threshed crop on the first third of the threshing roller and passing off some unthreshed parts of sunflower heads. To solve the aforementioned problem and optimize the efficiency of the sunflower threshing process, this research was focused on devising and testing a sunflower threshing machine with a close threshing box system equipped with a screw conveyor that evenly distributed the feedstock of sunflower heads on the entire length of the threshing roller. The machine was tested to assess the seed damage rate, unthreshed seed percentage, threshing efficiency, machine productivity, power requirements and specific energy consumption. The evaluation was done under different roller rotational speeds (150, 200, 250 and 300 rpm) and feeding rates (600, 700, 800 and 900 kg/h). The obtained results revealed that the threshing evaluation parameters were affected significantly by the roller rotational speed and feeding rate. The threshing efficiency was observed to rise with the rise in the roller rotational speed, and it also rose with the increasing feed rate up to 800 kg/h and then started to descend. The unthreshed seed percentage decreased with the increase in the roller rotational speed for all feed rates, and it decreased with the increasing feed rate up to 800 kg/h and then started to increase at the higher feed rates. The damaged seed percentage, power requirement and machine productivity increased with the increase of the roller speed and feed rate. The Buckingham π theorem was followed to find an equation to predict the threshing efficiency, resulting in an equation with an R2 value of 0.9309. With elimination of the blockage problem and better threshing efficiency, this machine could be a good choice for small- to medium-sized sunflower farms.

26 July 2024 in Agriengineering
Verified
Journal Article
Open access
PDF file
Muhammad TahirMuhammad Tahir
Muhammad Tahir
HMHafiz Sultan Mahmood
Hafiz Sultan Mahmood
MHMuzammil Husain
Muzammil Husain
AKAyesha Khalil
Ayesha Khalil
MSMuhammad Shoaib
Muhammad Shoaib
Muhammad Jehanzeb Masud CheemaMuhammad Jehanzeb Masud Cheema
Muhammad Jehanzeb Masud Cheema
In data-scarce regions, prudent planning and precise decision-making for sustainable development, especially in agriculture, remain challenging due to the lack of correct information. Remotely sensed satellite images provide a powerful source for assessing land use and land cover (LULC) classes and crop identification. Applying remote sensing (RS) in conjunction with the Geographical Information System (GIS) and modern tools/algorithms of artificial intelligence (AI) and deep learning has been proven effective for strategic planning and integrated resource management. The study was conducted in the canal command area of the Lower Chenab Canal system in Punjab, Pakistan. Crop features/classes were assessed using the Normalized Difference Vegetation Index (NDVI) algorithm. The Moderate Resolution Imaging Spectroradiometer (MODIS) 250 m and Landsat 5 TM (thematic mapper) images were deployed for NDVI time-series analysis with an unsupervised classification technique to obtain LULC classes that helped to discern cropping pattern, crop rotation, and the area of specific crops, which were then used as key inputs for agricultural mechanization planning and resource management. The accuracy of the LULC map was 78%, as assessed by the error matrix approach. Limitations of high-resolution RS data availability and the accuracy of the results are the concerns observed in this study that could be managed by the availability of good quality local sources and advanced processing techniques, that would make it more useful and applicable for regional agriculture and environmental management.

19 February 2023 in Agriculture
Verified
Journal Article
Open access
PDF file
Muhammad TahirMuhammad Tahir
Muhammad Tahir
JZJumin Zhang
Jumin Zhang
YZYong Zhou
Yong Zhou
Muhammad SultanMuhammad Sultan
Muhammad Sultan
Fiaz AhmadFiaz Ahmad
Fiaz Ahmad
JXJunfang Xia
Junfang Xia
Traction failure on loose terrain is common in conventional agricultural wheeled tractors due to poor traction ability and lower power transfer efficiency of drive wheels, which leads to excessive energy consumption and soil compaction in agriculture. To overcome the problem, this paper presents a new design of a rigid lugged wheel for use in field tillage operations. This wheel was designed according to field operational requirements and also provided with rubber pads for smooth on-road drives. Kinematic and dynamic analysis of new wheel designs were carried out to study how they move, how they interact with the soil, and how they generate drive force in loose terrain soil. The relationship of wheel lug motion trajectories, displacement, and velocity of the wheel relative to field conditions, different travel reduction rates, and lug penetration/wheel sinkage were analyzed. Wheel-terrain interaction and shear stress-shear displacement relationships when the wheel is driven in soft, deformable terrain were studied using classic soil mechanics principles. It is found that the component of thrust in the direction of driving, i.e., driving force, is ranged between 81.52% and 86.17%, while the vertical component is reported to be less than 30% and further decreases to 9%, which is the compaction avoiding factor. The relationships, thus developed, of wheel parameters, soil stress and thrust characteristics, and wheel drive force were derived and revealed that the traction performance, power transfer efficiency, and trafficability of tractors in loose terrain can be improved by using the newly proposed wheel. A finite element method was used to analyze the designed wheel model for structural stability and optimization. The theoretical analysis results of the new drive wheel are convincing, so further tests and field operation research are recommended for sustainable adoption.
2