In this paper, we used the multi-relaxation time lattice Boltzmann method to investigate natural convection in a triangular-shaped cavity filled with a tri-hybrid nanofluid. The cavity is partially heated by a chip of fixed size (l=L/2), the position of which varies on the left and bottom walls in order to find the optimal positions. The inclined side is maintained at a cool temperature, while the other parts are adiabatic. A detailed analysis is carried out on the impact of four essential parameters on the optimization of heat transfer: the Rayleigh number, ranging between Ra = 103 and Ra = 106; the partial heating position, showing the cavity in six different configurations; the fluid type, including pure water, nanofluid, hybrid nanofluid, and tri-hybrid nanofluid; and finally, the volume concentration of the nanoparticles for three values, ϕ = 0%, 3%, and 6%. Results are presented in the form of isotherms, streamlines, temperature and velocity profiles, and the mean Nusselt number values. As the results show, the position of the partial heater plays a crucial role, influencing natural convection heat transfer significantly in certain positions at all values of the Rayleigh number. The type of fluid has a remarkable impact on the amplification of natural convection at large values of the Rayleigh number, where the buoyancy force becomes strong. Notably, the use of tri-hybrid nanofluid shows a clear improvement in natural convection heat transfer. Furthermore, a substantial increase in thermal transmittance is observed with an increasing nanoparticle volume fraction. The validation results agree well with both numerical results and experimental data published in the literature.
12 February 2024 in Numerical Heat Transfer, Part A: Applications
The natural convection of incompressible flow confined within an enclosed right-angled triangular and isosceles cavity was investigated numerically using the multirelaxation time lattice Boltzmann method (MRT-LBM). According to the left and inclined walls thermal boundary conditions, two cases were considered in this study. In the first case, the inclined side of the enclosure was adiabatic, and the horizontal wall was heated, while the left one was kept at a cold temperature. However, the states of the left and inclined walls were interchanged in the second case. As the flow is only transported under the convection force, this study was carried out for the Rayleigh number ranging from to . The effects of the Rayleigh number on velocity and temperature profiles, streamlines, isotherms, and average Nusselt number were investigated. The position of cold and adiabatic walls had a great effect on the results. The results obtained are in good agreement with those of the literature and show the robustness of the MRT-LBM approach. In both cases, the heat-transfer rate increases with the increase in the Rayleigh number.
25 November 2020 in Modelling and Simulation in Engineering
Natural convection of gas flow (air) confined within an enclosed square-section cavity is investigated numerically using the lattice Boltzmann method (LBM). The right (left) side of the enclosure is partially heated (cooled) by a hot (cold) chip, while the left (right) one is completely kept at cold (hot) temperature. However, the horizontal walls and vertical parts near the chip are kept adiabatic. The buoyancy effect induced by the gravity acceleration, related to the convection force, is evaluated through the Rayleigh number in the range of 103-106 (laminar regime). The wall heating-ratio effect on the flow properties such as temperature and velocity profiles was examined. The heat transfer is analyzed through the Nusselt number for different chip lengths. Results show that the wall heat ratio has an interesting effect on the flow behavior. Results show good agreement with those of full natural convection in the literature, experimental, and simulation data.
17 November 2016 in Monte Carlo Methods and Applications
The steady state of a dilute gas enclosed within a rectangular cavity, whose upper and lower sides are in relative motion, is considered in the slip and early transition regimes. The DSMC (Direct simulation Monte Carlo) method is used to solve the Boltzmann equation for analysing a Newtonian viscous heat conducting ideal gas with the slip and jump boundary conditions (SJBC) in the vicinity of horizontal walls. The numerical results are compared with the Navier–Stokes solutions, with and without SJBC, through the velocity, temperature, and normal heat flux profiles. The parallel heat flux and shear stress are also evaluated as a function of rarefaction degree; estimated by the Knudsen number K n ${K_{n}}$ . Thus, the breakdown of the classical Navier–Stokes theory is clarified in the non-equilibrium area, so-called Knudsen layer, near the top and bottom sides.
19 March 2020 in Mathematical Problems in Engineering
In this paper, the Thermal Lattice Boltzmann Method (TLBM) is used for the simulation of a gas microflow. A 2D heated microchannel flow driven by a constant inlet velocity profile and nonisothermal walls is investigated numerically. Two cases of micro-Poiseuille flow are considered in the present study. In the first case, the temperature of the walls is kept uniform, equal to zero; therefore, the gas is driven along the channel under the inlet parameters of velocity and temperature. However, in the second one, the gas flow is also induced by the effect of temperature decreasing applied on the walls. For consistent results, velocity slip and temperature jump boundary conditions are used to capture the nonequilibrium effects near the walls. The rarefaction effects described by the Knudsen number, on the velocity and temperature profiles are evaluated. The aim of this study is to prove the efficiency of the TLBM method to simulate Poiseuille flow in case of nonisothermal walls, based on the average value of the Nusselt number and by comparing the results obtained from the TLBM with those obtained using the Finite Difference Method (FDM). The results also show an interesting sensitivity of velocity and temperature profiles with the rarefaction degree and the imposed temperature gradient of the walls.