Hussein M. Taqi Al-Najjar

Prof. Hussein M. Taqi Al-Najjar

University of Baghdad – College of Engineering, Department of Energy Engineering
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 January 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Farqad Talib NajimFarqad Talib Najim
Farqad Talib Najim
Hayder MohammedHayder Mohammed
Hayder Mohammed
HAHussein M. Taqi Al-Najjar
Hussein M. Taqi Al-Najjar
LTLakshmi Thangavelu
Lakshmi Thangavelu
MMMustafa Z. Mahmoud
Mustafa Z. Mahmoud
PTPouyan Talebizadeh
Pouyan Talebizadeh
Employing phase-change materials (PCM) is considered a very efficient and cost-effective option for addressing the mismatch between the energy supply and the demand. The high storage density, little temperature degradation, and ease of material processing register the PCM as a key candidate for the thermal energy storage system. However, the sluggish response rates during their melting and solidification processes limit their applications and consequently require the inclusion of heat transfer enhancers. This research aims to investigate the potential enhancement of circular fins on intensifying the PCM thermal response in a vertical triple-tube casing. Fin arrays of non-uniform dimensions and distinct distribution patterns were designed and investigated to determine the impact of modifying the fin geometric characteristics and distribution patterns in various spatial zones of the heat exchanger. Parametric analysis on the various fin structures under consideration was carried out to determine the most optimal fin structure from the perspective of the transient melting evolution and heat storage rates while maintaining the same design limitations of fin material and volume usage. The results revealed that changing the fin dimensions with the heat-flow direction results in a faster charging rate, a higher storage rate, and a more uniform temperature distribution when compared to a uniform fin size. The time required to fully charge the storage system (fully melting of the PCM) was found to be reduced by up to 10.4%, and the heat storage rate can be improved by up to 9.3% compared to the reference case of uniform fin sizes within the same fin volume limitations.

27 January 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
HAHussein M. Taqi Al-Najjar
Hussein M. Taqi Al-Najjar
Jasim M. MahdiJasim M. Mahdi
Jasim M. Mahdi
Dmitry BokovDmitry Bokov
Dmitry Bokov
NKNidhal Ben Khedher
Nidhal Ben Khedher
NAnaif alshammari
naif alshammari
PTPouyan Talebizadeh
Pouyan Talebizadeh
The melting duration in the photovoltaic/phase-change material (PV/PCM) system is a crucial parameter for thermal energy management such that its improvement can realize better energy management in respect to thermal storage capabilities, thermal conditions, and the lifespan of PV modules. An innovative and efficient technique for improving the melting duration is the inclusion of an exterior metal foam layer in the PV/PCM system. For detailed investigations of utilizing different metal foam configurations in terms of their convective heat transfer coefficients, the present paper proposes a newly developed mathematical model for the PV/PCM–metal foam assembly that can readily be implemented with a wide range of operating conditions. Both computational fluid dynamic (CFD) and experimental validations proved the good accuracy of the proposed model for further applications. The present research found that the average PV cell temperature can be reduced by about 12 °C with a corresponding improvement in PCM melting duration of 127%. The addition of the metal foam is more effective at low solar radiation, ambient temperatures far below the PCM solidus temperature, and high wind speeds in nonlinear extension. With increasing of tilt angle, the PCM melting duration is linearly decreased by an average value of (13.4–25.0)% when the metal foam convective heat transfer coefficient is changed in the range of (0.5–20) W/m2.K. The present research also shows that the PCM thickness has a positive linear effect on the PCM melting duration, however, modifying the metal foam configuration from 0.5 to 20 W/m2.K has an effect on the PCM melting duration in such a way that the average PCM melting duration is doubled. This confirms the effectiveness of the inclusion of metal foam in the PV/PCM system.

27 May 2023 in Journal of Building Engineering
Verified
Journal Article
Closed access
NKNidhal Ben Khedher
Nidhal Ben Khedher
Hussein TogunHussein Togun
Hussein Togun
AAAzher M. Abed
Azher M. Abed
HAHussein M. Taqi Al-Najjar
Hussein M. Taqi Al-Najjar
ADAnmar Dulaimi
Anmar Dulaimi
PTPouyan Talebizadeh
Pouyan Talebizadeh


1 October 2015 in Journal of Engineering
Verified
Journal Article
Open access
PDF file
HAHussein M. Taqi Al-Najjar
Hussein M. Taqi Al-Najjar
Firstly, in this study, a brief updated description and applications of different solar collectors used in renewable energy systems for supplying electric and thermal energy was presented. Secondly, an attempt was made to utilize tilting orientation of solar collector for maximizing collector energy with time in respect to horizontal orientation. For energy calculation, global solar radiation was used since they are directly related. For that purpose, field measurements of half-hourly radiation on two flat panels of tilting and horizontal orientations were carried out throughout 8-month period under local climate of Baghdad. Then, energy gain and radiation level averages were calculated based on the field radiation data using Excel programming. The tilting orientation was found to be more effective for the winter months with significant energy gains of larger than 40% and maximum gain of 58%. On the contrary, the radiation levels on collector were lower during winter months. Finally, for clear sky condition, the average solar radiations for tilting and horizontal orientations of collector were of 910 W/m2 and 713 W/m2 respectively.

1 January 2019 in FME Transactions
Verified
Journal Article
Open access
PDF file
HAHussein M. Taqi Al-Najjar
Hussein M. Taqi Al-Najjar
AEAkram W. Ezzat
Akram W. Ezzat
A detailed methodology is presented in this paper for the calculation of nucleate boiling safety margin (NBSM) in nuclear research reactors using a temperature function with three different thermal-hydraulic hot-spot analyses: nominal, cumulative and statistical for normal operating condition and coolant flow variation. A computer simulation program is developed for applying the methodology to the IRT-5000 reactor based on experimental core data. According to cumulative analysis as the over-conservative approach, the NBSM at normal operating condition of thermal power 5 MW and coolant velocity 1.672 m/s was 2.3% with reactor power limit 5.13 MW. However, during power or coolant flow trip condition, transient nucleate boiling would occur for short period at reactor shutdown. Of great importance, variation of NBSM with reactor operating condition for the different hot-spot analyses is found to be of strong linear correlation such that one analysis is sufficient to specify the results of the other analyses.