Jaehan Park

Prof. Jaehan Park

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
NJNarae Jung
Narae Jung
JPJaehan Park
Jaehan Park
SPSang-Hyun Park
Sang-Hyun Park
Seunghan OhSeunghan Oh
Seunghan Oh
SKSungtae Kim
Sungtae Kim
Young-Bum ParkYoung-Bum Park
Young-Bum Park
We examined whether recombinant human bone morphogenetic protein-2 (rhBMP-2) when applied to collagen membranes, would reinforce them during guided bone regeneration. Four critical cranial bone defects were created and treated in 30 New Zealand white rabbits, including a control group, critical defect only; group 1, collagen membrane only; group 2, biphasic calcium phosphate (BCP) only; group 3, collagen membrane + BCP; group 4, collagen membrane with rhBMP-2 (1.0 mg/mL); group 5, collagen membrane with rhBMP-2 (0.5 mg/mL); group 6, collagen membrane with rhBMP-2 (1.0 mg/mL) + BCP; and group 7, collagen membrane with rhBMP-2 (0.5 mg/mL) + BCP. After a 2-, 4-, or 8-week healing period, the animals were sacrificed. The combination of collagen membranes with rhBMP-2 and BCP yielded significantly higher bone formation rates compared to the other groups (control group and groups 1–5 < groups 6 and 7; p < 0.05). A 2-week healing period yielded significantly lower bone formation than that at 4 and 8 weeks (2 < 4 = 8 weeks; p < 0.05). This study proposes a novel GBR concept in which rhBMP-2 is applied to collagen membranes outside instead of inside the grafted area, thereby inducing quantitatively and qualitatively enhanced bone regeneration in critical bone defects.

30 March 2026 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Open access
SHSangmin Ham
Sangmin Ham
JMJinhong Min
Jinhong Min
JLJiho Lee
Jiho Lee
YPYoung-Bum Park
Young-Bum Park
Hoon KimHoon Kim
Hoon Kim
JPJaehan Park
Jaehan Park
The long-term clinical performance of conventional soft denture liners is limited by microbial colonization, poor adhesion, and plasticizer leaching. This study developed a polyurethane-acrylate soft denture liner enabling moldless fabrication through digital photolithography-based 3D printing. Two urethane-acrylate oligomers with different molecular weights (1K: 12900 g/mol, 2K: 18500 g/mol) were synthesized and mixed in five different ratios to investigate compositional effects on mechanical and viscoelastic behavior. Increasing the proportion of the 2K oligomer enhanced tensile strength and elongation, with compositions ≥1:1 (GR-C) showing mechanical performance comparable to conventional silicone-based soft liners. Dynamic mechanical analysis showed storage modulus values (0.50-0.65 MPa) within the oral mucosal elastic range (0.37-5.93 MPa), indicating damping capacity. Shore A hardness of all compositions remained within the extra-soft range after 30 days, satisfying ISO 10139-2. Under compressive loading, higher 1K content increased resistance to deformation, while GR-C demonstrated intermediate compressive stress at 10-30% strain. In terms of dimensional accuracy, GR-A and GR-D showed greater deviations than the other groups, with higher deviations along the x- and y-axes compared to the z-axis, and group- and axis-dependent patterns were observed. Optical rheometry revealed that increasing the 2K oligomer content reduced the storage modulus while increasing the loss modulus and loss tangent, indicating enhanced viscous behavior. Water sorption (13.1-14.9 μg/mm3) was within previously reported ranges, whereas solubility (12.3-16.2 μg/mm3) was comparatively higher. Near-surface degree of conversion approached 100% after post-polymerization. GR-C was selected as the optimized formulation and showed no cytotoxicity in an L929 cell assay. In the printability assessment using a novel digital workflow, GR-C exhibited a root-mean square (RMS) deviation of 0.619 mm. These results demonstrate that controlled oligomer composition enables tunable tensile, compressive, and viscoelastic properties in 3D-printable polyurethane-acrylate soft denture liners.

1 January 2026 in The Journal of Korean Academy of Prosthodontics
Verified
Journal Article
Open access
PDF file
SHSangmin Ham
Sangmin Ham
JKJaeyoung Kim
Jaeyoung Kim
SCSuji Chon
Suji Chon
JPJaehan Park
Jaehan Park
Hyeonjong LeeHyeonjong Lee
Hyeonjong Lee
함상민, et al. J Korean Acad Prosthodont. 2026 Jul;64(3):207-217. https://doi.org/10.4047/jkap.2026.64.3.207

31 August 2026 in Journal of Dental Rehabilitation and Applied Science
Verified
Journal Article
Open access
PDF file
SHSeung-Yoon Ham
Seung-Yoon Ham
JPJaehan Park
Jaehan Park
SSSOOYEON SHIN
SOOYEON SHIN
Seung-Yoon Ham, Jae-Han Park, Soo-Yeon Shin. J Dent Rehabil Appl Sci 2026;42:286-98. https://doi.org/10.14368/jdras.2026.42.3.286

1 May 2026 in BMC Oral Health
Verified
Journal Article
Open access
PDF file
SLSang-Seob Lee
Sang-Seob Lee
ACArmando Crupi
Armando Crupi
JPJaehan Park
Jaehan Park
Establishing an accurate occlusal vertical dimension (OVD) remains fundamental for prosthetic rehabilitation. Historically, a 40 mm vertical refer

31 December 2022 in Journal of Korean Dental Association
Verified
Journal Article
Open access
PDF file
JPJaehan Park
Jaehan Park
Occlusal bite forces are the most critical consideration factor in treatment planning. Measurement methods ofocclusal bite forces were developed in a century, and affected factors are studied in many experiments. Gender, age, shapes of facial morphology, teeth position, periodontal states, etc., are revealed affective aspects of theocclusal bite forces. The dental clinician should make a treatment plan by considering occlusal bite forces and would predict the patient's prognosis. In clinical procedures, several specific factors that include endodontic treatment, implant treatment, and com-plete denture prosthesis cause severe results after treatments. If clinicians do not consider these factors before the treatment procedures, extraction of the tooth, implant, and dismission of the complete denture are struggled by patients. These factors (endodontic treatment, Implant, complete denture prosthesis) cause the changes of occlusal bite forces, and then consideration of these changes makes a great result of treatment. The purpose of this study was to summarize the parts that clinicians can refer to based on reviewing studies on complex factors that affect occlusal bite force.