Jason Bettega

Dr. Jason Bettega

Department of Management and Engineering, University of Padua, Padua, Italy
orcid
Assistant Professor

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 February 2023 in Multibody System Dynamics
Verified
Journal Article
Open access
PDF file
Jason BettegaJason Bettega
Jason Bettega
GPGiulio Piva
Giulio Piva
Dario RichiedeiDario Richiedei
Dario Richiedei
ATAlberto Trevisani
Alberto Trevisani
This paper proposes a novel control scheme for precise path tracking control in cable driven parallel robots (CDPRs) with axially-flexible cables, with particular focus to the challenging case of cable suspended parallel robots (CSPRs). To handle model nonlinearities while ensuring small computational effort, a controller made by two sequential control actions is developed. The first term is a position-dependent, model predictive control (MPC) with embedded integrator to compute the optimal cable tensions ensuring accurate path tracking and fulfilling the feasibility constraints; bounds on the feasible tensions are also included. The second control term transforms the optimal tensions into the commanded motor torques, and hence currents, that are evaluated through the kinetostatic model of the electric motors used for winding and unwinding the cables. Control design is performed through the robot dynamics model, formulated with the assumption of rigid cables. Moreover, the proposed control strategy is presented in two different architectures, collocated control and noncollocated control. Flexibility is handled by penalizing large tension variations in the cost function adopted in the controller design, plus some hard constraints on the maximum tension derivatives. These features, together with the embedding of the integrator within the MPC formulation, ensure smooth control tensions that allow handling the axial flexibility of the cables, although it is not explicitly considered in the controller design.To assess the performances of the proposed control algorithm, a kinematically-determined robot with a suspended, lumped end-effector is simulated by also adopting very flexible cables. Additionally, a simplified dynamic model of the electrical dynamics and the sensor quantization are included to provide a realistic representation of the real environments. The results, together with the fair comparison with a benchmark, corroborate the effectiveness of the proposed approach, its robustness, and its feasibility in real-time controllers due to the wise reduction of the computational effort.


23 October 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
José Mario AraújoJosé Mario Araújo
José Mario Araújo
Jason BettegaJason Bettega
Jason Bettega
NDNelson José Bonfim Dantas
Nelson José Bonfim Dantas
CDCarlos E. T. Dorea
Carlos E. T. Dorea
Dario RichiedeiDario Richiedei
Dario Richiedei
Iacopo TamellinIacopo Tamellin
Iacopo Tamellin
This paper proposes a method for active vibration control to a two-link flexible robot arm in the presence of time delay, by means of robust pole placement. The issue is of practical and theoretical interest as time delay in vibration control can cause instability if not properly taken into account in the controller design. The controller design is performed through the receptance method to exactly assign a pair of pole and to achieve a given stability margin for ensuring robustness to uncertainty. The desired stability margin is achieved by solving an optimization problem based on the Nyquist stability criterion. The method is applied on a laboratory testbed that mimic a typical flexible robotic system employed for pick-and-place applications. The linearization assumption about an equilibrium configuration leads to the identification of the local receptances, holding for infinitesimal displacements about it, and hence applying the proposed control design technique. Nonlinear terms, due to the finite displacements, uncertainty, disturbances, and the coarse encoder quantization, are effectively handled by embedding the robustness requirement into the design. The experimental results, and the consistence with the numerical expectations, demonstrate the method effectiveness and ease of application.

25 January 2023 in Journal of Mechanisms and Robotics
Verified
Journal Article
Closed access
PDF file
Jason BettegaJason Bettega
Jason Bettega
Dario RichiedeiDario Richiedei
Dario Richiedei
Iacopo TamellinIacopo Tamellin
Iacopo Tamellin
ATAlberto Trevisani
Alberto Trevisani
An enhanced inverse dynamics approach is here presented for feedforward control of underactuated multibody systems, such as mechanisms or robots where the number of independent actuators is smaller than the number of degrees of freedom. The method exploits the concept of partitioning the independent coordinates into actuated and unactuated ones (through a QR-decomposition) and of linearly combined output, to obtain the internal dynamics of the nonminimum-phase system and then to stabilize it through proper output redefinition. Then, the exact algebraic model of the actuated sub-system is inverted, leading to the desired control forces with just minor approximations and no need for pre-actuation. The effectiveness of the proposed approach is assessed by three numerical test cases, by comparing it with some meaningful benchmarks taken from the literature. Finally, experimental verification through an underactuated robotic arm with two degrees of freedom is performed.

23 November 2022 in Journal of Vibration Engineering & Technologies
Verified
Journal Article
Open access
PDF file
Jason BettegaJason Bettega
Jason Bettega
Dario RichiedeiDario Richiedei
Dario Richiedei
Iacopo TamellinIacopo Tamellin
Iacopo Tamellin
ATAlberto Trevisani
Alberto Trevisani
Purpose: This paper proposes a motion planning technique for precise path and trajectory tracking in an underactuated, non-minimum phase, spatial overhead crane. Besides having a number of independent actuators that is smaller than the number of degrees of freedom, tip control on this system presents unstable internal dynamics that leads to divergent solution of the inverse dynamic problem. Method: The paper exploits the representation of the controlled output as a separable function of the actuated (i.e., the platform translations) and unactuated (i.e., the swing angles) coordinates to easily formulate the internal dynamics, without any approximation, and to study its stability. Then, output redefinition is adopted within the internal dynamics to stabilize it, leading to stable and causal reference commands for the platform translations. Results: Besides proposing the theoretical formulation of this novel method, the paper includes the numerical validation and the experimental application on a laboratory setup. Comparison with the state-of-the-art input shaping is also proposed. Conclusion: The results, obtained through different reference trajectories, clearly show that almost exact tracking is obtained also in the experiments, by outperforming the benchmarks.

8 June 2022 in Machines
Verified
Journal Article
Open access
PDF file
Jason BettegaJason Bettega
Jason Bettega
Dario RichiedeiDario Richiedei
Dario Richiedei
ATAlberto Trevisani
Alberto Trevisani
This paper proposes the preliminary results on a novel control architecture based on model predictive control (MPC) for cable-driven parallel robots (CDPRs) and applies them to a three degrees of freedom (3-DOF) robot with a suspended configuration, leading to a cable-suspended parallel robot (CSPR). The goal of the control scheme is ensuring accurate path tracking of the reference end-effector path, while imposing a priori positive cable tensions. To handle the nonlinearities characterizing the dynamic model that governs this kind of multibody system and to keep the computational effort low, a position-dependent MPC algorithm with an embedded integrator is designed to compute the optimal cable tensions required to track the end-effector commanded path. Such tensions must belong to the feasible domain defined through a lower bound, which is slightly greater than zero, to ensure that cables pull the end-effector, and an upper bound, to represent the maximum stress that cables can withstand without breaking. The resulting controller is nonlinear, although it performs a local linearization in the prediction at each time step to reduce the computational effort. The optimal tensions are then transformed into the commanded motor torques through the inverse dynamic model of the servomotors driving the winches, since no force measurement is adopted in the controller implementation. The control architecture is designed and numerically validated through a spatial CSPR with lumped end-effector, and driven by three cables (i.e., with a non-redundant configuration). Four different paths are assumed to highlight various features of the proposed controller.