The method of intersection of surfaces generated by kinematic dyads is applied to obtain mechanisms that are able to shift from one mode of motion to another. Then a mobility analysis shows that the singularities of the generated surfaces can be used to obtain mechanisms which can change their number of degrees-of-freedom depending on its configuration. The generator dyads are connected as usually done by a spherical pair. However, in the cases shown in this contribution the three-degrees-of-freedom of the spherical pair are not all necessary to keep the kinematic chain closed and movable, and the spherical pair can be substituted by either a pair of intersecting revolute joints or a single revolute joint. This substitution can be obtained by means of two methods presented in this contribution.
1 March 2018 in Journal of Mechanisms and Robotics
This paper for the first time reveals a set of special plane-symmetric Bricard linkages with various branches of reconfiguration by means of intersection of two generating toroids, and presents a complete theory of the branch reconfiguration of the Bricard plane-symmetric linkages. An analysis of the intersection of these two toroids reveals the presence of coincident conical singularities, which lead to design of the plane-symmetric linkages that evolve to spherical 4R linkages. By examining the tangents to the curves of intersection at the conical singularities, it is found that the linkage can be reconfigured between the two possible branches of spherical 4R motion without disassembling it and without requiring the usual special configuration connecting the branches. The study of tangent intersections between concentric singular toroids also reveals the presence of isolated points in the intersection, which suggests that some linkages satisfying the Bricard plane-symmetry conditions are actually structures with zero finite degrees-of-freedom (DOF) but with higher instantaneous mobility. This paper is the second part of a paper published in parallel by the authors in which the method is applied to the line-symmetric case.
28 January 2016 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Kinematic chains are obtained from the helicoid–helicoid intersections applying the method of surfaces generated by kinematic dyads. Some local properties of the helicoids are used to obtain the bifurcation points in the configuration space of the obtained kinematic chains. It is proven that certain relationships between the two helicoids lead to a periodic behavior of these bifurcations, which suggest that, if the kinematic pairs (P and H) could move without a limit, the kinematic chain would theoretically feature an infinity of operation modes. Finally, a mechanism which is able to change the helicoid–helicoid intersection curve during its motion is proven to change its finite mobility in one of its operation modes.
23 March 2018 in Journal of Mechanisms and Robotics
This paper for the first time investigates a family of line-symmetric Bricard linkages by means of two generated toroids and reveals their intersection that leads to a set of special Bricard linkages with various branches of reconfiguration. The discovery is made in the concentric toroid–toroid intersection. By manipulating the construction parameters of the toroids, all possible bifurcation points are explored. This leads to the common bi-tangent planes that present singularities in the intersection set. The study reveals the presence of Villarceau and secondary circles in the toroid–toroid intersection. Therefore, a way to reconfigure the Bricard linkage to a pair of different types of Bennett linkage is uncovered. Further, a linkage with two Bricard and two Bennett motion branches is explored. In addition, the paper reveals the Altmann linkage as a member of the family of special line-symmetric Bricard linkage studied in this paper. The method is applied to the plane-symmetric case in the following paper published together with this paper.
15 March 2021 in Journal of Mechanisms and Robotics
This contribution presents a screw theory-based method for determining the mobility of fully parallel platforms. The method is based on the application of three stages. The first stage involves the application of the intersection of subalgebras of Lie algebra, se(3), of the special Euclidean group, SE(3), associated with the legs of the platform. The second stage analyzes the possibility of the legs of the platform generating a sum or direct sum of two subalgebras of the Lie algebra, se(3). The last stage, if necessary, considers the possibility of the kinematic pairs of the legs satisfying certain velocity conditions; these conditions reduce the platform’s mobility analysis to one that can be solved using one of the two previous stages. Several examples are illustrated.