The current trend in the use of remote sensing technologies is their use as a tool for monitoring hard-to-reach areas, objects or phenomena in the alpine environment. Remote sensing technology is also effectively used to monitor geohazards and the development of human-made changes in the country. Research presented in this study demonstrates the results for the usability of the publicly available national digital elevation model DEM 5.0 obtained by utilizing the airborne laser scanning (ALS) survey to monitor the development of erosion, morphological changes of talus cones, or the dynamics of movement of rock blocks between stages of measurement in the alpine environment of the High Tatras mountains. The reference methods for this study are the terrestrial laser scanning (TLS) and structure-from-motion (SfM) photogrammetric approach using unmanned aerial systems (UASs). By comparing the created DEMs, the ALS point cloud’s accuracy on mostly rocky areas of different sizes was verified. The results show that the standard deviation of the ALS point cloud ranges from 19 to 46 mm depending on the area’s size and characteristics. The maximum difference ranges from 100 to 741 mm. The value of systematic displacement of data obtained by different technologies ranges from 1 to 29 mm. This research confirms the suitability of the ALS method with its advantages and limits for the detection of movement of rock blocks or change of position of any natural or anthropogenic objects with a size from approximately 1 m2.
A frequently recurring problem in the extraction of mineral resources (especially heterogeneous mineral resources) is the rapid operative determination of the extracted quantity of raw material in a surface quarry. This paper deals with testing and analyzing the possibility of using unconventional methods such as digital close-range photogrammetry and terrestrial laser scanning in the process of determining the bulk density of raw material under in situ conditions. A model example of a heterogeneous deposit is the perlite deposit Lehôtka pod Brehmi (Slovakia). Classical laboratory methods for determining bulk density were used to verify the results of the in situ method of bulk density determination. Two large-scale samples (probes) with an approximate volume of 7 m3 and 9 m3 were realized in situ. 6 point samples (LITH) were taken for laboratory determination. By terrestrial laser scanning (TLS) measurement from 2 scanning stations, point clouds with approximately 163,000/143,000 points were obtained for each probe. For Structure-from-Motion (SfM) photogrammetry, 49/55 images were acquired for both probes, with final point clouds containing approximately 155,000/141,000 points. Subsequently, the bulk densities of the bulk samples were determined by the calculation from in situ measurements by TLS and SfM photogrammetry. Comparison of results of the field in situ measurements (1841 kg∙m−3) and laboratory measurements (1756 kg∙m−3) showed only a 4.5% difference in results between the two methods for determining the density of heterogeneous raw materials, confirming the accuracy of the used in situ methods. For the determination of the loosening coefficient, the material from both large-scale samples was transferred on a horizontal surface. Their volumes were determined by TLS. The loosening coefficient for the raw material of 1.38 was calculated from the resulting values.
Mapping watercourses and their surroundings through remote sensing methods is a fast, continuous, and effective method and is a crucial tool for capturing change and possibly predicting hazards. Thanks to Synthetic Aperture Radar (SAR) technology and the ability of its backscattered and emitted radiation to penetrate the atmosphere under any conditions, this type of mapping of water surfaces is of particular importance. This paper presents the possibility of using SAR technology for long-term observations of changes in the behaviour of rivers and river systems, combined with optical multispectral images Sentinel-2. Additionally, it aims to demonstrate the suitability of satellite SAR and multispectral data implementation for mapping changes in watercourses, caused not only by their natural development but especially by inundation processes in their catchment area. Appropriate Sentinel-1 image processing evaluation procedures demonstrate that the usage of vertical-vertical (VV) type polarisation configuration is a suitable methodology for documenting water bodies, and a Lee filter is an acceptable tool for radar noise filtering. The extraction process of water surfaces is based on the determination of threshold values using the “Otsu” principle. Subsequently, the comparison of the results is realised by the spectral indices of water—the Normalized Difference Water Index (NDWI), Modified Normalized Difference Water Index (MNDWI), a pair of Automated Water Extraction Index (AWEI) indices, and supervised classification method Maximum Likelihood Classification (MLC). The results are numerical and graphical evaluated. In assessing the accuracy of SAR extraction, the highest values achieved in Overall Accuracy (OA) were a maximum of 98.6%. On average, the lower values were in User Accuracy (UA) with a maximum of 93.1%, where VV polarisation also dominates. However, vertical-horizontal (VH) polarisation dominates in Producer Accuracy (PA) with a maximum of 84.9%.
The Ochtiná Aragonite Cave (Slovakia, Central Europe) is a world-famous karst phenomenon of significant geological, geomorphological, and mineralogical values. Its specific origin is determined by particular lithological and hydrogeological conditions of the Ochtiná karst formed in lenses of Paleozoic crystalline limestones, partly metasomatically altered to ankerite and siderite. Although the cave is only 300 m long, it represents a combined labyrinth consisting in parallel tectonically controlled halls and passages, that are largely interconnected through transverse conduits of phreatic and epiphreatic morphology with many medium- and small-scale forms originated in slowly moving or standing water (flat solution ceilings, wall inward-inclined facets, water table notches, convectional cupolas, and spongework-like hollows). The highly dissected and irregular morphologies of the cave were surveyed with terrestrial laser scanning and digital photogrammetry. Both used surveying technologies proved to be suitable for quick and accurate mapping of the complicated cave pattern. While terrestrial laser scanning can provide a rapid survey of larger and more complex areas with results delivered directly in the field, digital photogrammetry is able to generate very high-resolution models with quality photo-texture for mapping of small-scale morphologies. Several data on cave morphometry were generated from terrestrial laser scanning (e.g., the area of cave ground plan, the peripheral surface of underground spaces, and their volume). The new detailed map, sections, and 3D model create an innovation platform for a more detailed study on the morphology and genesis of this unusual cave also for its environmental protection and use in tourism.
This research focused on determining a rotary kiln’s geometric parameters in a non-traditional geodetic way—by deriving them from a survey realized by a terrestrial laser scanner (TLS). The point cloud obtained by TLS measurement was processed to derive the longitudinal axis of the RK. Subsequently, the carrier tires’ geometric parameters and shell of the RK during the shutdown were derived. Manual point cloud selection (segmentation) is the base method for removing unnecessary points. This method is slow but precise and controllable. The proposed analytical solution is based on calculating the distance from each point to the RK’s nominal axis (local radius). Iteration using a histogram function was repeatedly applied to detect points with the same or similar radiuses. The most numerous intervals of points were selected and stored in separate files. In the comparison, we present the conformity of analytically and manually obtained files and derived geometric values of the RK-radiuses’ spatial parameters and coordinates of the carrier tires’ centers. The horizontal (X and Y directions) and vertical (Z-direction) of root–mean–square deviation (RMSD) values are up to 2 mm. RMSD of the fitting of cylinders is also up to 2 mm. The center of the carrier tires defines the longitudinal axis of the RK. Analytical segmentation of the points was repeated on the remaining point cloud for the selection of the points on the outer shell of the RK. Deformation analysis of the shell of the RK was performed using a cylinder with a nominal radius. Manually and analytically processed point clouds were investigated and mutually compared. The calculated RMSD value is up to 2 mm. Parallel cuts situated perpendicularly to the axis of the RK were created. Analysis of ovality (flattening) of the shell was performed. Additionally, we also present the effect of gradually decreasing density (number) of points on the carrier tires for their center derivation.
13 March 2020 in Geomatics and Environmental Engineering
The main goal of the paper is to make a general assessment of the application of 3D technologies in spatial planning. It was performed with the city of Krakow as the case study. The paper describes the outline of the spatial planning system in Poland and the planning conditions of Krakow. The data obtained from laser scanning for Krakow are also briefly characterized. The possibility of using these data for locating high-rise buildings in terms of the protection of Krakow’s panorama and within two programs “IT system of the Country’s Protection Against Extreme Hazards” (ISOK) and “Integrated spatial data monitoring system for air quality improvement in Krakow” (MONIT-AIR) were analyzed in the paper. The main result of the research is the assessment of what studies or measurements may be used to meet particular spatial planning needs or requirements.