The extensive use of veterinary antibiotics worldwide has led to their increasing accumulation in aquatic environments, adversely affecting both ecosystems and human health and leading to the emergence of antibiotic-resistant bacteria. Antibiotic residues enter water bodies primarily through wastewater effluent discharge, agricultural runoff, and improper disposal of pharmaceuticals. Several emerging technologies have been developed in response to the challenge of antibiotic contamination in wastewater. Among these, advanced oxidation processes (AOPs), including photocatalysis, have demonstrated significant potential for antibiotic degradation. Photocatalysis relies on the production of powerful oxidants to degrade pollutants under simulated or solar-light irradiation. Apart from the well-known TiO2, various photocatalytic materials have been used with metal oxides on the frontline. In this context, metal doping has been used to reduce the bandgap energy and enhance the absorption of visible light and charge-carrier separation. Doping with non-metals and carbon-based materials is another attractive alternative that promotes better degradation efficiency and suppresses recombination. Moreover, advanced designs, such as heterojunction constructions, have been developed for effective charge separation and wider utilization of the light spectrum. This comprehensive review summarizes recent advances in the design, characterization, efficiency, and mechanisms of various photocatalysts for degrading veterinary antibiotics in wastewater, along with toxicity assessments of the resulting transformation products. By examining these parameters, the current body of knowledge is consolidated, providing valuable insights into wastewater purification processes for effective antibiotic removal. Finally, by emphasizing the critical environmental importance of streamlined photocatalysis and the challenges associated with scaling up the process, this review highlights its feasibility in mitigating veterinary antibiotic pollution, thereby safeguarding aquatic ecosystems and reducing the risks of antibiotic resistance.
Wastewater treatment has attracted much attention in recent years as a potential source of water, and there are some concerns about its safety for human use. Eco-friendly and cost-effective adsorbent materials were successfully synthesized from several peels, such as orange, banana, pomegranate, avocado, kiwi, etc., and were used as natural adsorbents or as activated carbons derived from these peels for water and wastewater treatment. In this review, the latest research focusing on the effective modification of these peels for the removal of several pollutants found in wastewaters are summarized and compared, such as pharmaceuticals, dyes, heavy metals, and anions that are released in waste and have a negative impact on human and animal health. In this review, focus is given to activated carbon produced from fruit peels. Moreover, fruit peels as adsorbent materials, without previously being converted to activated carbon, are of limited use in the recent literature.
The remediation of wastewaters contaminated with dyes (discharged mainly from industry) is very important for preserving environmental quality and human health. In this study, a new composite chitosan (CS)-based adsorbent combined with activated carbon (AC) and curcumin (Cur) (abbreviated hereafter as CS/AC@Cur) in three different ratios (12.5%, 25%, and 50%) was synthesized for the removal of anionic [reactive black 5 (RB5)] and cationic [methylene blue (MB)] dyes in single-component or binary systems. The synthesized materials were completely characterized through Fourier transform infrared spectroscopy, scanning electron microscopy, Brunauer-Emmett-Teller analysis, and X-ray diffraction. Specifically, a decrease in the surface area of CS/AC@ was observed with the addition of curcumin, from 163 to 18 m2/g, for all CS/AC@Cur derivatives. In terms of the adsorption results, the optimal derivative for the removal of both RB5 and MB was found to be CS/AC@Cur50%, providing 93% removal at pH 2.0 ± 0.1 for RB5 and 54% removal at the optimum pH of 9.0 ± 0.1 due to electrostatic attractions. The Elovich and pseudo-second-order kinetic model, with a correlation coefficient R2 of >0.98, better tailored the results, indicating that adsorption was controlled by chemisorption. In addition, the Sips (Langmuir-Freundlich) isotherm model fitted better to the results, with calculated capacities of 338 and 307 mg/g for RB5 and MB, respectively. The thermodynamic analysis showed a spontaneous and endothermic procedure, with chemisorption as the main mechanism. Reuse experiments showed that the removal efficiency was retained at high levels, while stability studies revealed that the adsorbent retains its structural integrity, even at extreme pH values. Finally, the adsorption of RB5 and MB in a mixed solution was investigated, providing a competitive effect between the anionic and cationic dyes.