The oxidation level of the conductive polymer PEDOT:PSS is influenced by an electrostatic field of ionic liquid.

Cellulose nanofibril (CNF) films were prepared from side streams generated by the sugarcane industry, that is, bagasse. Two fractionation processes were utilized for comparison purposes: (1) soda and (2) hot water and soda pretreatments. 2,2,6,6‐Tetramethylpiperidinyl‐1‐oxyl‐mediated oxidation was applied to facilitate the nanofibrillation of the bagasse fibers. Poly(ethylene glycol) (PEG) was chosen as plasticizer to improve the ductility of CNF films. The neat CNF and biocomposite films (CNF and 40% PEG) were used for fabrication of self‐standing humidity sensors. CNF‐based humidity sensors exhibited high change of impedance, within four orders of magnitude, in response to relative humidity (RH) from 20 to 90%. The use of plasticizer had an impact on sensor kinetics. While the biocomposite film sensors showed slightly longer response time, the recovery time of these plasticized sensors was two times shorter in comparison to sensors without PEG. This study demonstrated that agroindustrial side streams can form the basis for high‐end applications such as humidity sensors, with potential for, for example, packaging and wound dressing applications. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 47920.

The authors demonstrate, in this work, a fascinating synergism of a high surface area heterojunction between TiO₂ in the form of ordered 1D anodic nanotube layers of a high aspect ratio and ZnO coatings of different thicknesses, produced by atomic layer deposition. The ZnO coatings effectively passivate the defects within the TiO₂ nanotube walls and significantly improve their charge carrier separation. Upon the ultraviolet and visible light irradiation, with an increase of the ZnO coating thickness from 0.19 to 19 nm and an increase of the external potential from 0.4–2 V, yields up to 8‐fold enhancement of the photocurrent density. This enhancement translates into extremely high incident photon to current conversion efficiency of ≈95%, which is among the highest values reported in the literature for TiO₂ based nanostructures. In addition, the photoactive region is expanded to a broader range close to the visible spectral region, compared to the uncoated nanotube layers. Synergistic effect arising from ZnO coated TiO₂ nanotube layers also yields an improved ethanol sensing response, almost 11‐fold compared to the uncoated nanotube layers. The design of the high‐area 1D heterojunction, presented here, opens pathways for the light‐ and gas‐assisted applications in photocatalysis, water splitting, sensors, and so on.

A systematic study was carried out to investigate the effect of ionic liquid in solid polymer electrolyte (SPE) and its layer morphology on the characteristics of an electrochemical amperometric nitrogen dioxide sensor. Five different ionic liquids were immobilized into a solid polymer electrolyte and key sensor parameters (sensitivity, response/recovery times, hysteresis and limit of detection) were characterized. The study revealed that the sensor based on 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][N(Tf)₂]) showed the best sensitivity, fast response/recovery times, and low sensor response hysteresis. The working electrode, deposited from water-based carbon nanotube ink, was prepared by aerosol-jet printing technology. It was observed that the thermal treatment and crystallinity of poly(vinylidene fluoride) (PVDF) in the solid polymer electrolyte influenced the sensitivity. Picture analysis of the morphology of the SPE layer based on [EMIM][N(Tf)₂] ionic liquid treated under different conditions suggests that the sensor sensitivity strongly depends on the fractal dimension of PVDF spherical objects in SPE. Their deformation, e.g., due to crowding, leads to a decrease in sensor sensitivity.