Kwang Joon Kim

Mr. Kwang Joon Kim

Department of Mechanical Engineering, Graduate school, Korea University
+1
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 February 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Kwang Joon KimKwang Joon Kim
Kwang Joon Kim
Young-Gwan KimYoung-Gwan Kim
Young-Gwan Kim
KKKwon-Hee Kim
Kwon-Hee Kim
Burrs form due to the plastic deformation of materials during machining processes, such as milling and drilling. Deburring can be very difficult when the burrs are not easily accessible for removal. In this study, abrasive flow machining (AFM) was adopted for deburring the edges of milling specimens. Based on the experimental observations on AL6061 specimens, the deburring performance was characterized in terms of flow speed, the local curvature of the streamline near the burr edge, and shear stress. A new objective function that can predict the extent of deburring is proposed based on these characteristics and validated through milling burr edge erosion tests by abrasive flow. Based on the assumption that the flow component is tangential to the burr edge has relatively little contribution to the edge erosion, an attempt was made for the application of the new objective function to the three-dimensional burr edge formed by two intersecting holes drilled with offset. The deburring test results and predictions from three-dimensional computational fluid dynamics’ (CFD) simulations were in reasonable agreement.

8 February 2021 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
Young-Gwan KimYoung-Gwan Kim
Young-Gwan Kim
Kwang Joon KimKwang Joon Kim
Kwang Joon Kim
KKKwon-Hee Kim
Kwon-Hee Kim

27 February 2024 in IEEE Access
Verified
Journal Article
Open access
YCYoungsu Cho
Youngsu Cho
Kwang Joon KimKwang Joon Kim
Kwang Joon Kim
JPJongwoo Park
Jongwoo Park
HSHyunuk Seo
Hyunuk Seo
HJHyunmok Jung
Hyunmok Jung
CPChanhun Park
Chanhun Park
Stair climbing is necessary to improve the convenience of electric wheelchairs. An important issue in developing a climbable wheelchair is stability and speed during climbing. In this work, tri-wheel and supporting leg were adopted in the stair climbing method for high speed and stable posture. Based on the mechanical and static analyses of the climbing mechanism, the design method of the wheel cluster system was expressed as equations. These equations were proposed considering the design parameters that ensure the continuity and stability of the climbing motion. Moreover, the collision information between the stairs and the cluster system during the climbing motion was included in those equations. A validation test of the stair climbing mechanism was performed by manufacturing a prototype of 750 ( W ) x 800( D ) x 1,000( H ) mm 3 and 120 kg . The experimental verification proved that the electric wheelchair can stably go up and down the stairs under extreme conditions (stair width = 300 mm , stair height = 180 mm ) at a speed of 10 steps/min.

27 January 2022 in Preprints.org
Verified
Preprint
Open access
Kwang Joon KimKwang Joon Kim
Kwang Joon Kim
Young-Gwan KimYoung-Gwan Kim
Young-Gwan Kim
KKKwon-Hee Kim
Kwon-Hee Kim
Burrs form due to plastic deformation of materials during machining processes, such as milling and drilling. Deburring can be very difficult when the burrs are not easily accessible for removal. In this study, abrasive flow machining (AFM) was adopted for deburring the edges of milling specimens. Based on the experimental observations on AL6061 specimens, the deburring performance was characterized in terms of flow speed, the local curvature of the streamline near the burr edge, and shear stress. A new objective function that can predict the extent of deburring is proposed based on these characteristics and validated through experiments. Based on this new objective function, a prediction of deburring performance on the burr edge of the intersecting holes with offset was performed. The results between the predicted and experimental observation results were in reasonable agreement.