Laidi Babouri

Prof. Dr. Laidi Babouri

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 December 2024 in Buildings
Verified
Journal Article
Open access
PDF file
RBRahima Baghloul
Rahima Baghloul
Laidi BabouriLaidi Babouri
Laidi Babouri
HHHouria Hebhoub
Houria Hebhoub
FBFouad Boukhelf
Fouad Boukhelf
YMYassine El Mendili
Yassine El Mendili
The quarrying and utilization of natural stones such as marble and granite are growing rapidly in developing countries. However, the processing, cutting, sizing, and shaping of these stones to render them functional generates huge quantities of waste and dust. These materials are often disposed of openly in the environment, and their potentially hazardous nature has negative repercussions on both the environment and human health. In this study, marble waste (MW) was used as a filler in the unsaturated polyester resin (UPR) matrix to enhance performance and characteristics while adding value to the waste and minimizing manufacturing costs. For this purpose, samples of UPR/MW composites were produced with 0, 5, 10, 15, and 20 wt.% of MW incorporated into the UPR. A full characterization that focused on the microstructure, thermal stability, and physical and mechanical properties was carried out. The results revealed that the use of 10 to 15% of MW improves mechanical performance, with increases from 17 to 26 kJ/m2, 14 to 17 MPa, and 794 to 1522 GPa in impact strength, tensile strength, and elastic modulus, respectively. By introducing a 20% MW filler, the composite loses its performance, particularly Shore D hardness, and becomes very brittle. Thermogravimetric analysis (TGA) indicated significant thermal stabilization, with a delay in the start decomposition temperature of 28 °C for 20 UPR/MW compared to 0 UPR/MW. Additionally, morphological and microstructural tests, namely, FT-IR, XRD, and SEM analysis, show a microstructural change, including the formation of crystalline phases, enhancing matrix-filler interactions due to the creation of Mg-O and Ca-O chemical bonds and the forming of filler agglomeration at high introduction rates that lead to defects in the microstructure. These results confirmed the mechanical results of the UPR/MW composites.

29 October 2020 in European Journal of Environmental and Civil Engineering
Verified
Journal Article
Closed access
Laidi BabouriLaidi Babouri
Laidi Babouri
YBYasmina Biskri
Yasmina Biskri
Fouzia KHADRAOUIFouzia KHADRAOUI
Fouzia KHADRAOUI
YMYassine El Mendili
Yassine El Mendili
In this work, the performance of reinforced concrete containing different percentages of marble filler as a partial substitution of ordinary Portland cement is investigated. The cement is replaced by marble accordingly in the range of 5, 10, 15 and 20 wt.% for concrete. The measurements of flexural and compressive strengths are conducted on the concrete with marble dust. The corrosion behaviour of reinforced concrete in the aggressive medium (3% NaCl) is carried out using the potentiodynamic polarisation and impedance spectroscopy. From the outcome of this investigation, the partial substitution of cement by up to 20% of marble in concrete is achieved without compromising the overall strength. For all mixtures, the maximum compressive and flexural strengths at all curing ages are obtained with a 5% replacement of cement by marble. The greater effectiveness of marble waste is attributed to its higher calcium content and CO32– ions release, which lead to the formation of carboaluminate hydrates, then to further porosity reduction that increases the strengths. The results also show that the steel bars in reinforced concrete prepared with 5% of marble have better corrosion to that in the ordinary reinforced concrete.

10 October 2025 in Innovative Infrastructure Solutions
Verified
Journal Article
Closed access
PDF file
SKSoumaya Kersenna
Soumaya Kersenna
AHAbdelaziz Hammouda
Abdelaziz Hammouda
S. M. AnasS. M. Anas
S. M. Anas
BYBiskri Yasmina
Biskri Yasmina
Laidi BabouriLaidi Babouri
Laidi Babouri
Mohammed BenzeraraMohammed Benzerara
Mohammed Benzerara

14 August 2026 in Processes
Verified
Journal Article
Open access
PDF file
ASAbdelmalek Saoud
Abdelmalek Saoud
Laidi BabouriLaidi Babouri
Laidi Babouri
CACheraitia Abdallah
Cheraitia Abdallah
FBFouad Boukhelf
Fouad Boukhelf
S. M. AnasS. M. Anas
S. M. Anas
Seif El Islam LebouacheraSeif El Islam Lebouachera
Seif El Islam Lebouachera
The valorization of agricultural waste into high-value carbon nanomaterials offers dual benefits: it reduces pollution and provides low-cost materials for sustainable technologies. This work synthesizes graphene-like carbon from Ghars date waste via mild KOH-assisted pyrolysis at 1000 °C. The material (G-GhW1000) exhibits a sharp (002) XRD peak at 26.16° (d-spacing = 3.40 Å), a characteristic π → π* transition at 253 nm, and a high C/O ratio of 27.37. Dispersed in tap water (0.5 g/L) by simple hand shaking (without ultrasonication), it serves as a photothermal nanofluid in a modified single-slope solar still (MSS). Under outdoor conditions, the MSS produces 4.69 L·m−2·day−1, which is 18.7% higher than a conventional still, with thermal efficiency rising from 27.2% to 30.8% (with a reproducible 19.0% enhancement in summer). Samples prepared at 800 °C and 900 °C give 4.0% and 6.4% lower yields, while the 1100 °C sample gives only 6.0% improvement, confirming 1000 °C as the optimal temperature. The superior performance at 1000 °C is attributed to the optimal balance between graphitization, deoxygenation, and structural integrity, as evidenced by XRD, FTIR, EDX and UV-Vis analyses. The enhanced performance is linked to higher water temperature (68 °C) and larger ΔT. The distilled water meets WHO standards (TDS 9.35 mg/L, >99.4% reduction) with no detectable graphene-like carbon carryover. This work demonstrates the potential of waste-derived graphene-like carbon as a low-cost additive for solar desalination, addressing water scarcity and waste management within a circular economy framework. To our knowledge, this is the first study to use Ghars date waste-derived graphene-like carbon in a solar still.