Li Wang

Prof. Dr. Li Wang

Guangdong University of Petrochemical Technology, Maoming, Guangdong, China
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 January 2010 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
LWLi Wang
Li Wang
LCLi Chen
Li Chen
ZYZongcheng Yan
Zongcheng Yan
HWHonglin Wang
Honglin Wang
JPJiazhi Peng
Jiazhi Peng

1 August 2019 in Advances in Polymer Technology
Verified
Journal Article
Open access
PDF file
WFWen Fu
Wen Fu
LWLi Wang
Li Wang
JHJianning Huang
Jianning Huang
CLCuiwen Liu
Cuiwen Liu
WPWenlong Peng
Wenlong Peng
SLShenglin Li
Shenglin Li
The obvious polarity difference between the carbon black (CB) and the natural rubber (NR) causes the CB hard to be dispersed in the NR matrix when the addition amount is large. In this paper, polyethylene glycol (PEG) was grafted onto the surface of CB by the liquid phase. The grafted carbon black (GCB) was prepared and applied to reinforce NR. The main physical and mechanical properties of NR were improved because of the better compatibility between GCB and NR. The Mullins effect of the vulcanizate was calculated by the cyclic stress-strain experiment. The results showed that the Mullins effect both existed in the virgin NR system and filled NR system. The degree of Mullins effect was increased with the increase of the filler addition, but that was different for CB and GCB. When the filler addition was below 20 phr, the Mullins effect of NR/GCB was stronger than that of NR/CB. However, when the filler addition was over 30 phr, the Mullins effect of NR/CB was stronger than that of NR/GCB. The Mullins effect was affected by the heat treatment temperature and time. The mechanisms of the Mullins effect were analyzed.

18 May 2016 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
WFWen Fu
Wen Fu
LWLi Wang
Li Wang

12 May 2022 in Membranes
Verified
Journal Article
Open access
PDF file
LWLi Wang
Li Wang
WFWen Fu
Wen Fu
GYGuangkun Yi
Guangkun Yi
ZCZiyang Chen
Ziyang Chen
WFWen Fu
Wen Fu
QPQingyu Pan
Qingyu Pan
ZrO2 was coated on AZ31 magnesium alloy substrate by plasma electrolytic oxidation with K2ZrF6 and NaH2PO4 electrolytes. The discharge characteristics and variation in active species during the plasma electrolytic oxidation (PEO) process were studied by optical emission spectroscopy. The surface morphology and element composition of the membranes were observed by scanning electron microscope. The ion transfer of the substrate was studied by atomic absorption spectroscopy. The phase composition and corrosion characteristics of the PEO membranes were examined with XRD and an electrochemical workstation, respectively. The heat and mass transfer models during the PEO process were introduced. The contributions of ions to the membranes and active species were also analyzed. The results indicated that the ion transfer at different stages exhibits different tendencies. At the first and transition stages, the migration resistance of the ions was low and increased gradually. At the initial discharge stage, the migration resistance was the highest because the highest membrane growth rate occurred at this stage. At the later discharge stage, the migration resistance tends to be stable, which is ascribed to a dynamic equilibrium PEO membrane growth rate. The intensity of active species is related to the energy state of the working electrode’s surface. The higher the energy, the greater the probability that the active species will be excited to generate energy level transitions, and the higher the plasma concentration.

18 July 2023 in Processes
Verified
Journal Article
Open access
PDF file
JSJIN SUN
JIN SUN
Haoshui YuHaoshui Yu
Haoshui Yu
ZYZengqi Yin
Zengqi Yin
LJLiangliang Jiang
Liangliang Jiang
LWLi Wang
Li Wang
RZRujin Zhou
Rujin Zhou
In a fuel-based refinery, rich gas in the fluid catalytic cracking (FCC) unit is further processed to separate dry gas and refinery products (i.e., stabilized gasoline and liquified petroleum gas). The process is utility-intensive and costly and includes a two-stage compressor, pumps, an absorber, a stripper, a stabilizer, and a re-absorber. The optimization was conducted with respect to the compressor outlet pressure from the gas compression system (GCS) and the flow rate of absorbent and supplementary absorbent from the Absorption-stabilization System (ASS) using the process simulation software Aspen Plus. Compared to the base case of a 725 kt/a rich gas FCC unit, a refinery can save 2.42% of utility costs under optimal operation. Through optimized operation, medium-pressure steam consumption has been reduced by 2.4% compared to the base case, resulting in a significant improvement in total operational cost. The optimization strategy can provide insightful guidance for the practical operation of GCS and ASS.

13 May 2022 in Membranes
Verified
Journal Article
Open access
PDF file
WFWen Fu
Wen Fu
LWLi Wang
Li Wang
ZHZhuohang Huang
Zhuohang Huang
XHXiaoyan Huang
Xiaoyan Huang
ZSZhijin Su
Zhijin Su
QPQingyu Pan
Qingyu Pan
Processing robust mechanical properties is important for elastomeric materials. In this work, different molecular weights of polyethylene glycols (PEG) were used to modify graphene oxide (GO) in order to study the relationship between the number of hydrogen bonds and the properties of the polyurethane/graphene oxide membrane. The fact of PEG was successfully grafted onto the surface of GO was certified by Fourier transform infrared spectra, Raman spectra, X-ray photoelectron spectroscopy. The graft ratio was indicated by thermogravimetric analysis. The presence of hydrogen bonds in PUR/MGO composites membrane was proved by the cyclic loading-unloading test and stress relaxation test. The thermal stability and low-temperature resistance performance of PUR/MGO had been improved compared with PUR/GO. When the molecular weight of PEG grafted on the surface of GO was 600, the tensile strength and elongation at break of the composite membrane were optimal. The reason for the improvement of physical and mechanical properties was that the dispersion of filler in the rubber matrix and the compatibility between filler and rubber had been improved.