The obvious polarity difference between the carbon black (CB) and the natural rubber (NR) causes the CB hard to be dispersed in the NR matrix when the addition amount is large. In this paper, polyethylene glycol (PEG) was grafted onto the surface of CB by the liquid phase. The grafted carbon black (GCB) was prepared and applied to reinforce NR. The main physical and mechanical properties of NR were improved because of the better compatibility between GCB and NR. The Mullins effect of the vulcanizate was calculated by the cyclic stress-strain experiment. The results showed that the Mullins effect both existed in the virgin NR system and filled NR system. The degree of Mullins effect was increased with the increase of the filler addition, but that was different for CB and GCB. When the filler addition was below 20 phr, the Mullins effect of NR/GCB was stronger than that of NR/CB. However, when the filler addition was over 30 phr, the Mullins effect of NR/CB was stronger than that of NR/GCB. The Mullins effect was affected by the heat treatment temperature and time. The mechanisms of the Mullins effect were analyzed.
17 November 2016 in Journal of Macromolecular Science, Part B
Carbon black (CB) was modified by liquid grafting and used for natural rubber (NR) reinforcement. Payne effects during NR reinforcement by the graft-modified carbon black (GCB) were analyzed in this paper. The results showed a proportional relationship between filler content and the Payne effect. Rubber compounds with GCB presented weaker Payne effects than their non-modified counterparts. Qualitative analysis of the correlation between filler network structure and filler content was conducted according to the relationship between bound rubber of a rubber compound and shear modulus. The impact of the storage period on the Payne effect was further studied, and the results demonstrated that the longer the storage period of the rubber compound, the stronger the Payne effect tended to be. The mechanisms by which the Payne effects were manifested differed according to the content of the filler in the rubber.
ZrO2 was coated on AZ31 magnesium alloy substrate by plasma electrolytic oxidation with K2ZrF6 and NaH2PO4 electrolytes. The discharge characteristics and variation in active species during the plasma electrolytic oxidation (PEO) process were studied by optical emission spectroscopy. The surface morphology and element composition of the membranes were observed by scanning electron microscope. The ion transfer of the substrate was studied by atomic absorption spectroscopy. The phase composition and corrosion characteristics of the PEO membranes were examined with XRD and an electrochemical workstation, respectively. The heat and mass transfer models during the PEO process were introduced. The contributions of ions to the membranes and active species were also analyzed. The results indicated that the ion transfer at different stages exhibits different tendencies. At the first and transition stages, the migration resistance of the ions was low and increased gradually. At the initial discharge stage, the migration resistance was the highest because the highest membrane growth rate occurred at this stage. At the later discharge stage, the migration resistance tends to be stable, which is ascribed to a dynamic equilibrium PEO membrane growth rate. The intensity of active species is related to the energy state of the working electrode’s surface. The higher the energy, the greater the probability that the active species will be excited to generate energy level transitions, and the higher the plasma concentration.
Processing robust mechanical properties is important for elastomeric materials. In this work, different molecular weights of polyethylene glycols (PEG) were used to modify graphene oxide (GO) in order to study the relationship between the number of hydrogen bonds and the properties of the polyurethane/graphene oxide membrane. The fact of PEG was successfully grafted onto the surface of GO was certified by Fourier transform infrared spectra, Raman spectra, X-ray photoelectron spectroscopy. The graft ratio was indicated by thermogravimetric analysis. The presence of hydrogen bonds in PUR/MGO composites membrane was proved by the cyclic loading-unloading test and stress relaxation test. The thermal stability and low-temperature resistance performance of PUR/MGO had been improved compared with PUR/GO. When the molecular weight of PEG grafted on the surface of GO was 600, the tensile strength and elongation at break of the composite membrane were optimal. The reason for the improvement of physical and mechanical properties was that the dispersion of filler in the rubber matrix and the compatibility between filler and rubber had been improved.
This paper attempted to achieve the purpose of increasing the tensile strength and toughness of polyurethane rubber (PUR) simultaneously by introducing polyethylene glycol (PEG) onto the surface of graphene oxide (GO) to introduce hydrogen bond interactions into the PUR-GO system. GO was grafted with PEG and added to PUR by mechanical blending. The polyethylene glycol-g-graphene oxide (MGO) was characterized by infrared spectroscopy, Raman spectroscopy, X-ray diffraction, and thermogravimetric analysis. The PUR/MGO composites were tested by tensile testing machine, thermogravimetric analysis, dynamic thermal analysis, and scanning electron microscopy. The results demonstrated that PEG was successfully grafted onto the surface of GO and the grafting rate was about 37%. The grated PEG did not affect the crystalline structure of GO. The addition of MGO could improve the thermal stability of PUR vulcanizate. After the addition of GO, the glass transition temperature (Tg) of vulcanizate was shifted to higher temperature. However, the Tg of vulcanizate reinforced by MGO was shifted to lower temperature. The strength and toughness of vulcanizate were significantly improved by adding MGO. The reason was that the hydrogen bond interactions between MGO and PUR were destroyed and the hidden length was released during the strain process. A lot of energy was consumed, and thus the strength and toughness of PUR vulcanizate were improved.