The theoretical analysis of corrosion processes on the periodical profile reinforcement in low potential corrosion environment has been conducted using a mathematical model. The boundary between liquid and metal phases in the model was set by a sinusoidal laxly concaved profile. In this research, it’s been suggested the hypothesis that mass transfer of cathodic and anodic depolarizers on the surface of corroborated reinforcement is defined by diffusion such that current density is constant on long distance from the boundary between the phases. The Laplacian equation has been solved by perturbation method representing concentrations as mathematical row by a small parameter. It has been analyzed the possibility of occurring a liquid coating under the concrete protective layer on the reinforcement surface in the contact spots between the ribs and reinforcement body. It’s been discovered how the profile geometry impacts the distribution of corrosion current.
Інженерно-геологічні умови більшої частини території України характеризуються наявністю лесових просадочних ґрунтів, товщина яких може сягати до 30 метрів. У таких умовах зведення промислових і цивільних будівель висотою понад п’ять поверхів доцільно здійснювати на палях різних типів. Ґрунтоцемент являє собою матеріал, що утворюється внаслідок змішування природного ґрунту з цементом. У результаті формується міцна структура, стійка до впливу вологи та здатна витримувати значні навантаження. Цей матеріал активно використовується для створення ґрунтоцементних паль. Елементи меншого діаметра на його основі застосовуються для підсилення слабких ґрунтів, формуючи зону стабілізованої основи. Палі з ґрунтоцементу можуть служити надійною основою для будівель і споруд різного призначення, а також виконувати функції протифільтраційних екранів, підпірних конструкцій, укріплень укосів котлованів і зсувних ділянок. Крім того, ґрунтоцемент ефективно використовується як матеріал для облаштування дорожнього покриття. В роботі розглянуто підбір оптимального складу ґрунтоцементної суміші. Планування експериментів та підбір складу ґрунтоцементу враховували різну витрату цементу і водоцементне відношення (В/Ц), а також добавки. Критерієм експерименту призначено міцність грунтоцементу на стиск (призмова міцність). Склад цементно-ґрунтових сумішей підбирався у лабораторії таким чином, щоб забезпечити отримання ґрунтоцементу з заданими міцностними характеристиками при мінімальній витраті цементу. Були виготовленні та випробувані на стиск дослідні зразки. Випробування виконували за допомогою преса при терміні набору міцності 7, 28, 56 діб Також розглянуті польові дослідження структури грунтоцементного елементу після 6 місяців твердіння. Елементи були відкопані і досліджені по глибині за допомогою метода пенетрації. Основною задачею досліджень було визначення міцності ґрунтоцементу за довжиною палі.Для перевірки ефективності армування основи у конкретних умовах будівельного майданчика були проведені дослідження її стисливості шляхом випробовування ґрунтів штампом. Перевірка стисливості основи була проведена у природному і зволоженому станах ґрунту до та після його армування.
The article summarises the first domestic experience in designing and implementing electrochemical (cathodic) protection against corrosion of reinforcement in reinforced concrete structures exposed to aggressive environments. It considers examples of such protection for structures of many buildings and constructions with different operation conditions. The study examines the first instance in the domestic practice of testing electrochemical (cathodic) protection against reinforcement corrosion in concrete columns. The reinforcement of reinforced concrete structures in the lower part of the columns underwent corrosion due to frequent spills of aggressive solutions from the floor. There were drainage trays on the floor located near the columns that need protection, parallel to their transverse rows, to collect and remove these spills. These trays served to house linear anodes of cathodic protection. Anodes made of individual metal rods were placed on the bottom of the trays and covered with an electrically conductive solution. After determining the anodic areas on the reinforced concrete floor beams, they developed a project for cathodic reinforcement protection. Coating the reinforced concrete beams with polymer paints during the repair works did not lead to a decline in corrosion processes on their fittings in some areas. Given the initial conditions, the decision was to adopt an electrochemical protection scheme with selective distribution of metal foil anodes on conductive paint on the surface of the beams. The conducted examination of the concentrated sulfuric acid shop showed that reinforcement corrosion in reinforced concrete structures occurs under the action of solutions of acid spills and their steam. Corrosion intensifies in some parts of structures. In the columns, such places appear in the lower sections, where the structures are in contact with the environment (spills). In the proposed cathodic protection system, a regulated current source allowed for obtaining a constant current of up to 10 A. A 1–2 cm thick layer of electrically conductive solution was applied to the lower part of the columns under restoration. Lead anodes were embedded into the conductive solution. A working project was developed for cathodic protection of the reinforced concrete deck of the bridge in its reconstruction on the highway. The bridge suffered significant damage primarily due to corrosion in the reinforced concrete deck. In the existing conditions, active methods of protecting reinforced concrete structures have proven more profitable. The structural solution of the bridge facilitates the use of electrochemical protection. The concrete protective layer of the roadway includes reinforcing metal grids that serve as anodes. All reinforcement of reinforced concrete structures is a part of a single electrical circuit. The research goal is to improve the technological properties of the reinforcement electrochemical protection installation in reinforced concrete slabs. The installation solves the task of reducing labour costs and material consumption of protection systems. A solution to this task is freeing the seam between the plates from filling materials and laying a flexible electrical insulating tape in the formed gap, which has a longitudinal perforated surface in the form of a reach-through in the middle. When laying, the tape receives a U-shaped cross-section, creating a trough in the gap between the plates that has a perforated bottom. A wire anode fits into the created trough. The proposed device is easy to implement and replace elements during operation. The galvanic anode, which simultaneously serves as a reinforcing element of the stretched zone in reinforced concrete beams, is characterised by its versatility. The reinforcing element is made in the shape of a tape, while the metal has a higher electrochemical potential than the reinforcing metal. This metal tape is placed on the conductive solution and connected to the reinforcing frame of the beam. Further improvement of the cathodic protection systems of the reinforced concrete structures needs to draw on the accumulated practical experience of its application. Keywords: reinforcement of reinforced concrete structures, corrosion, cathodic protection.