Makhmudun Ainuri

Dr. Makhmudun Ainuri


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 February 2023 in International Journal of Biomaterials
Verified
Journal Article
Open access
PDF file
SSSusi Susi
Susi Susi
MAMakhmudun Ainuri
Makhmudun Ainuri
WWWagiman Wagiman
Wagiman Wagiman
MFMohammad Affan Fajar Falah
Mohammad Affan Fajar Falah
Oil palm empty fruit bunches (OPEFB) are lignocellulosic materials that are a by-product of the palm oil industry, which have less use and utilization is still limited. OPEFBs high cellulose content could potentially develop into various bioproducts, especially biomaterials. The thermochemical delignification process can obtain high-yieldalpha-cellulose. The cellulose extraction process can be done by combining the bleaching process under acidic conditions and alkaline delignification to obtain high-purity cellulose. The bleaching conditions vary in the concentration of NaClO2, the length of bleaching, the temperature, and the number of stages. The research obtains high α-cellulose by optimizing bleaching conditions under acidic conditions in celluloses OPEFB extraction with variability on NaClO2 concentration and bleaching time using response surface methodology (RSM). The bleaching process was implemented at an early stage with a concentration of 3 NaClO2 and a bleaching time of 2hours as a center point with a bleaching cycle of twice at pH 44.5 using acetic acid. Bleached fibers were delignified using 10 NaOH for 2hours at room temperature. The RSM analysis resulted in optimum bleaching conditions at a concentration of 3.22 NaClO2 for 1hour, yielding OPEFBs cellulose of 82.96±2.53, hemicellulose of 9.27±2.28, and lignin of 1.68±0.58. The validation and verification process in the bleaching conditions obtained cellulose of 84.87 and α-cellulose of 88.51, with a crystallinity index of 70.55 and crystallite size of 2.35nm. Scanning electron microscopy on surface cellulose morphology at optimum bleaching helped remove hemicellulose impurities, lignin, and inorganic materials and a more intensive opening of cellulose fibrils. The bleaching process optimization point was verified to improve the delignification performance and potentially produce high yield α-cellulose content for microcrystalline cellulose use.

1 December 2022 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
SSS Susi
S Susi
MAMakhmudun Ainuri
Makhmudun Ainuri
WWW Wagiman
W Wagiman
MFM A F Falah
M A F Falah
Oil palm empty fruit bunches (OPEFB) have not been properly utilized by most palm oil mills and communities in Indonesia. The processing and utilization of OPEFB by palm oil mills are still limited. Due to high cellulose contents, it potentially made into various bioproducts, especially as biomaterials. Therefore, a proper extraction technology is needed to obtain a high level of cellulose purity because alkaline treatment can solely remove a part of hemicellulose and lignin. A higher cellulose content can be obtained by further chemical treatments through the bleaching process. However, no information regarding the difference of the isolation performance method to produce cellulose purity by delignification first or vice versa bleaching as an initial stage. The research determined the purity of EFB cellulose with differences in the sequence of bleaching and alkaline delignification stages. The three methods were carried, namely the first method by bleaching using sodium chlorite 3% two times, followed by delignification of NaOH 10% at room temperature, second method with the same conditions but delignification of NaOH 10% at a temperature of 70-80°C and third method by delignification and continued bleaching under the same conditions. The results showed the bleaching method of sodium chlorite of 2 cycles and continued by alkaline delignification (NaOH 10%) at room temperature resulted in higher cellulose purity than other methods. The FTIR test results indicated the detection of the C-O functional group at a wavelength of 1196 cm-1 and the C-H functional group at a wavelength of 2967 cm-1.

1 January 2024 in Journal of Renewable Materials
Verified
Journal Article
Open access
PDF file
SSSusi Susi
Susi Susi
MAMakhmudun Ainuri
Makhmudun Ainuri
WWWagiman Wagiman
Wagiman Wagiman
MFMohammad Affan Fajar Falah
Mohammad Affan Fajar Falah
Microcrystalline cellulose (MCC) is one of the cellulose derivatives produced as a result of the depolymerization of a part of cellulose to achieve high crystallinity. When implemented in other polymers, high crystallinity correlates with greater strength and stiffnes, but it can reduce the water-holding capacity. The acid concentration and hydrolysis time will affect the acquisition of crystallinity and water absorption capacity, both of which have significance as properties of hydrogel filler. The study aimed to evaluate the properties and select the MCC generated from varying the proportion of hydrochloric acid (HCl) and the appropriate hydrolysis time as a filler for film hydrogel. MCC was produced by hydrolyzing cellulose of oil palm empty fruit bunches (OPEFB) with the HCl solution at varied concentrations and periods. The results show that the longer hydrolysis times and higher HCl concentrations increase crystallinity and density while lowering yield and water absorption. The extensive acid hydrolysis reduces the amorphous area significantly, allowing the depolymerization to occur and extend the crystalline area. The morphological properties of the MCC, which are smaller but compact, indicate the presence of disintegrating and diminishing structures. A 2.5 N HCl concentration and a 45-min hydrolysis time succeed in sufficient crystallinity as well as maintaining good water absorption capacity. The treatment produced MCC with absorption capacity of 4.03 ± 0.26 g/g, swelling capacity of 5.03 ± 0.26 g/g, loss on drying of 1.44% ± 0.36, bulk and tapped density of 0.27 ± 0.031 g/cm3 and 0.3 ± 0.006 g/cm3, respectively, with a crystallinity index of 88.89% ± 4.76 and a crystallite size of 4.23 ± 0.70 nm. The MCC generated could potentially be utilized as a hydrogel film filler, since a given proportion will be able to maintain the strength of the hydrogel, not readily dissolve but absorb water significantly.

1 January 2024 in International Journal of Chemical Engineering
Verified
Journal Article
Open access
SSSusi Susi
Susi Susi
MAMakhmudun Ainuri
Makhmudun Ainuri
WWWagiman Wagiman
Wagiman Wagiman
MFMohammad Affan Fajar Falah
Mohammad Affan Fajar Falah
Carboxymethyl cellulose (CMC), a water‐soluble cellulose, can be derived from oil palm empty fruit bunches (OPEFBs). In addition to being highly soluble, it is essential for CMC to exhibit excellent thermal stability when utilized in biocomposites. Reactants in the alkalization and etherification steps to provide high DS of CMC‐based OPEFB have not been standardized. The research aimed to optimize the alkalization and etherification processes using a response surface methodology (RSM). This will help in determining the optimal ratios of 30% NaOH (the center point of 3), isopropanol (the center point of 30) as maceration media, and monochloroacetic acid (the center point of 1.2) needed for the cellulose. RSM determined the optimum ratio of 30% NaOH to OPEFB cellulose, which was 3.36 : 1, an isopropanol ratio of 30.62 : 1, and an MCA to cellulose ratio of 1.19 : 1. The optimization indicates that the OPEFB cellulose‐based CMC have a high degree of substitution of 1.28 and a carboxymethyl content of 31.93%. CMC morphology showed noticeable changes, such as a smoother surface and swelling. There was a significant increase in the wavenumber of 1580 cm−1 due to the presence of carbonyl groups. The OPEFB‐based CMC resulted in a crystallinity of 40.18%, and thermal gravimetric analysis indicated that mass decreases occurred at high temperatures of 500°C, which suggests that the optimal CMC has a high thermal stability. OPEFB‐based CMC exhibits a high degree of substitution and resistance to thermal degradation, which makes it suitable for further use as the main material in biocomposite films.

19 February 2025 in Energies
Verified
Journal Article
Open access
PDF file
AAArief Abdurrakhman
Arief Abdurrakhman
LSLilik Sutiarso
Lilik Sutiarso
MAMakhmudun Ainuri
Makhmudun Ainuri
MUMirwan Ushada
Mirwan Ushada
MIMd. Parvez Islam
Md. Parvez Islam
Efficient biogas production significantly impacts greenhouse gas (GHG) emissions and carbon sequestration by reducing emissions and enhancing carbon storage. Nonetheless, the consistency and optimization of biogas production are hindered by fluctuations in key input variables, namely, pH, moisture content, organic loading rate (OLR), and temperature, which significantly impact the quality of agricultural waste biomass and biogas production. Any fluctuations in these variables can affect biogas productivity. This study aims to provide valuable optimization parameters for maximum biogas production using rice straw and cow dung as agricultural waste biomass for biogas input materials. Therefore, machine learning techniques such as multilayer perceptron feedforward neural networks with a particle swarm optimization (PSO) combination generate optimal values for each variable for maximum biogas production. This study uses three variants of the training function for neural networks, namely gradient descent with momentum and adaptive learning rate, gradient descent with momentum, and gradient descent with adaptive learning rate. The findings reveal that, under an optimum pH value of 6.0000, a humidity of 62.3176%, an OLR of 67.6823 kg.m3/day, and a temperature of 37.0482 °C, biogas production has the potential to increase to 2.91 m³/day with a high accuracy testing value of R2 = 0.90. These methods in use accurately predict the optimal parameters, with a maximum deviation of 8.48% from experimentally derived values and mean square error (MSE) of 0.0051243. This study emphasizes the benefits of using multilayer perceptron feedforward neural networks and particle swarm optimization to optimize operational parameters and accurately predict biogas production.

1 January 2026 in International Journal of Biomaterials
Verified
Journal Article
Open access
SSSusi Susi
Susi Susi
MAMakhmudun Ainuri
Makhmudun Ainuri
WWWagiman Wagiman
Wagiman Wagiman
MFMohammad Affan Fajar Falah
Mohammad Affan Fajar Falah
HHHisyam Musthafa Al Hakim
Hisyam Musthafa Al Hakim
Cellulose‐based hydrogel films are promising alternatives to plastic for wrapping. Hydrogel films based on carboxymethyl cellulose (CMC) and microcrystalline cellulose (MCC) must exhibit high mechanical strength and be capable of absorbing moisture. Crosslinking increases the absorption capacity and mechanical strength of hydrogel films. As a filler, MCC can synergize with citric acid, which acts as an environmentally friendly crosslinker to enhance mechanical strength. This research aimed to develop a suitable CMC/MCC formulation and citric acid as a crosslinker, resulting in a hydrogel with high water absorption and mechanical strength. CMC/MCC formulations were combined with citric acid concentrations of 5%, 7.5%, and 10%. The results showed that the MCC and citric acid will affect absorption and mechanical strength. The addition of MCC up to 50% tends to produce a brittle hydrogel film, and this phenomenon is also correlated with increased citric acid. A 90:10 CMC/MCC formulation with 5% citric acid (w/v) resulted in a water uptake of 222.72 ± 9.32 at pH 7.0. In contrast, the 80:20 CMC/MCC formulation resulted in a water uptake of 603.02 ± 26.98. They both showed higher rehydration of the dry gel than the others. FTIR confirmed the sharpening of the peak wave number at 1705 cm −1 , which is identical to the protonated carbonyl group and correlates with the water absorption capacity. The morphology of hydrogel films containing a CMC/MCC ratio of 90:10 exhibits a smoother surface than that of those with a CMC/MCC ratio of 80:20, which feature bubbles on the surface cracks of the hydrogel film due to the presence of more water absorption channels. Hydrogel films with a CMC/MCC ratio of 90:10 and 5% citric acid (w/v) can be developed for wrapping by modifying their hygroscopic properties. In contrast, hydrogel films with an 80:20 ratio and 5% citric acid are suitable for use as absorbents.