Sporadic ocean color events with characteristic spectra, in particular algal blooms, call for quick delivery of high-resolution remote sensing data for further analysis. Motivated by this, we present the mission design for HYPerspectral Smallsat for Ocean observation (HYPSO-1), a 6U CubeSat at 500 km orbital altitude hosting a custom-built pushbroom hyperspectral imager with wavelengths 387–801 nm at 3.33 nm bandpass and a swath width of 70 km. The imager’s expected signal-to-noise ratio is characterized for typical open ocean water-leaving radiance which can be flexibly increased by binning pixels. Using geometric principles, the satellite shall execute a slew maneuver during a scan to induce greater overlap in the pixels with a goal to enable better than 100 m spatial resolution. Since high-dimensional hyperspectral data need to be transmitted over limited space-to-ground communications, we have designed a modular FPGA-based onboard image processing architecture that significantly reduces the data size without losing important spatial-spectral information. We justify the concept with a simulated scenario where HYPSO-1 first collects numerous hyperspectral images of a 40 km by 40 km coastal area in Norway and aims to immediately transfer these to nearby ground stations. Using CCSDS123 lossless compression, it takes about one orbital revolution to obtain the complete data product when considering overhead in satellite bus communications and less than 10 min without the overhead. It is shown that even better latency can be achieved with more advanced onboard processing algorithms.
The HYPSO-1 satellite, a 6U CubeSat carrying a hyperspectral imager, was launched on 13 January 2022, with the Goal of imaging ocean color in support of marine research. This article describes the development and current status of the mission and payload operations, including examples of agile planning, captures with low revisit time and time series acquired during a campaign. The in-orbit performance of the hyperspectral instrument is also characterized. The usable spectral range of the instrument is in the range of 430 nm to 800 nm over 120 bands after binning during nominal captures. The spatial resolvability is found empirically to be below 2.2 pixels in terms of Full-Width at Half-Maximum (FWHM) at 565 nm. This measure corresponds to an inherent ground resolvable resolution of 142 m across-track for close to nadir capture. In the across-track direction, there are 1216 pixels available, which gives a swath width of 70 km. However, the 684 center pixels are used for nominal captures. With the nominal pixels used in the across-track direction, the nadir swath-width is 40 km. The spectral resolution in terms of FWHM is estimated to be close to 5 nm at the center wavelength of 600 nm, and the Signal-to-Noise Ratio (SNR) is evaluated to be greater than 300 at 450 nm to 500 nm for Top-of-Atmosphere (ToA) signals. Examples of images from the first months of operations are also shown.
26 September 2018 in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
Hyperspectral imaging (HSI) can extract information from scenes on the earth surface acquired by airborne or spaceborne sensors. On-board processing of HSI is characterized by large datasets on one side and limited processing time and communication links on the other. The CCSDS-123 algorithm is a compression standard assembled for space-related application that allows compacted data transmission via a transmission link. In this paper, a low-complexity high-throughput field-programmable gate array (FPGA) implementation of CCSDS-123 compression algorithm with band interleaved by pixel ordering is presented. Hardware accelerators implemented in FPGAs are increasingly used for custom tasks due to their efficiency, low power, and reconfigurability. The proposed implementation of CCSDS-123 compression standard has been tested on ZedBoard development board containing a Zynq-7020 FPGA. The results are verified against an existing software implementation. The synthesized design can perform on-the-fly processing of hyperspectral images with maximum operating frequency of 147 MHz. The achieved throughput of 147 Msamples/s (2.35 Gb/s) is higher when compared with the throughput reported in recent state-of-the-art FPGA implementations.
9 November 2010 in IEEE Transactions on Instrumentation and Measurement
This paper presents an open-source virtual instrument for time-frequency analysis. The purpose is to show the correct practical implementation, and the performance, of a number of complex algorithms and of a practical criterion (the concentration measure) to select the proper algorithm for a given signal. The virtual instrument provides efficient solutions for signals with a highly nonstationary instantaneous frequency. Despite variations of signal phase function, a high concentration can be achieved by a suitable choice of distribution form. The distribution can be chosen manually, or the instrument can perform optimal distribution selection. Namely, a procedure for the automated selection of optimal distribution order is provided. The concentration measure is employed as a selection criterion. A variety of options provides different comparisons for several distributions simultaneously. Efficiency of the proposed instrument is demonstrated on various examples. It is important to emphasize that an extensive and complex theory is implemented as a set of open-source algorithms. All the algorithms can be used “as is” or modified and upgraded (even separately) by researchers and practitioners in the field. The virtual instrument is available at http://www.tfsa.ac.me/Open_source_codes.html,, or upon request to the authors.
Satellite onboard processing for hyperspectral imaging applications is characterized by large data sets, limited processing resources and limited bandwidth of communication links. The CCSDS-123 algorithm is a specialized compression standard assembled for space-related applications. In this paper, a parallel FPGA implementation of CCSDS-123 compression algorithm is presented. The proposed design can compress any number of samples in parallel allowed by resource and I/O bandwidth constraints. The CCSDS-123 processing core has been placed on Zynq-7035 SoC and verified against the existing reference software. The estimated power use scales approximately linearly with the number of samples processed in parallel. Finally, the proposed implementation outperforms the state-of-the-art implementations in terms of both throughput and power.
Hyperspectral imaging is a powerful remote sensing technology, but its use in space is limited by the large volume of data it produces, which leads to a downlink bottleneck. Therefore, most payloads to date have been oriented towards demonstrating the scientific usefulness of hyperspectral data sporadically over diverse areas rather than detailed monitoring of spatio-spectral dynamics. The key to overcoming the data bandwidth limitation is to process the data on-board the satellite prior to downlink. In this article, the design, implementation, and in-flight demonstration of the on-board processing pipeline of the HYPSO-1 cube-satellite are presented. The pipeline provides not only flexible image processing but also reliability and resilience, characterized by robust booting and updating procedures. The processing time and compression rate of the simplest pipeline, which includes capturing, binning, and compressing the image, are analyzed in detail. Based on these analyses, the implications of the pipeline performance on HYPSO-1’s mission are discussed.