This article describes the manufacturing of a horn antenna using a 3D commercial printer. The horn antenna was chosen for its simplicity and practical versatility. The standardised horn antenna is one of the most widely used antennas in microwave technology. A standardised horn antenna can be connected to standardised waveguides. The horn antenna has been selected so that this antenna can be fabricated by 3D printing and thus obtain the equivalent of a standardised horn antenna. This 3D horn antenna can then be excited by a standardised waveguide. The 3Dprinted horn antenna with metallic layers has very good impedance characteristics, standing wave ratio and radiation patterns that are close to those of a standardised horn antenna. The 3D-based horn antenna is suitable for applications where low antenna weight is required, such as aerospace and satellite technologies. The article also describes a manufacturing procedure for a horn antenna (E-sector horn antenna) that is plated with galvanic layers of silver and gold. The design of the plated horn antenna in the Matlab application using the Antenna Toolbox extension is also described, including 3D printing procedures, post-processing procedures (plating) and practical testing of its functionality. The measured results are compared to simulations of the standardised horn antenna and then analysed.
Malicious UAVs pose a growing threat. There are various ways to counter such devices. This article discusses the use of noise and EMP to jam drones. In this work, an analysis of the UAV communication signals was performed and two experiments were conducted to investigate the effects of noise jamming and EMP on the UAV control channel.
This article describes the effect of high-power electromagnetic environments (HPEMs) on the operation of all basic elements of electrical power networks. Frequency bands are defined for the HPEM environments. Attention is focused particularly on directed energy weapons (DEWs) and intentional electromagnetic interference (IEMI). A classification of DEW and IEMI generators in terms of E-field level and target distance from the DEW or IEMI generator antenna aperture is also described. The main focus of this article is on the design and testing of a low-tech DEW generator used to determine the electromagnetic immunity of standard electronic circuits. In addition, verification of electromagnetic immunity for a simple electronic circuit without adequate protection against the E-field is also explained. The outcome of this article is the determination of the E-field limits for fault-free operation, for malfunctioning states of the tested circuits and for irreversible destruction of the circuits. The measured E-field was compared to basic microwave radiation theory and to simulation results in COMSOL Multiphysics software (COMSOL, Inc. 100 District Avenue Burlington, MA 01803 USA).
This paper presents the manufacturing of a patch antenna using an advanced 3D printing technology called lights-out digital additive manufacturing (LDM). This 3D LDM printing technology is mainly used for printing circuit boards (PCBs); however, it has also been used to print a patch antenna from conductive (CI) and dielectric ink (DI). This 3D LDM-printed antenna was compared with antennas on different dielectric substrates (Arlon 25N and FR4). The obtained results are compared and analyzed in this paper.
Artykuł dotyczy zagadnienia precyzyjnego sterowania silnikami krokowymi. Silniki krokowe są używane w wielu aplikacjach ze względu na ich właściwości w zakresie dokładności i kontroli prędkości. W niniejszym artykule zaproponowano aplikację do precyzyjnego pozycjonowania przestrajalnego bocznika falowodu. Do tego zastosowania używany jest specjalny typ silnika krokowego zwany siłownikiem liniowym.. (Precyzyjne sterowanie silnikami krokowymi do przestrajalnego bocznika falowodu)
This paper describes the design and construction of a remotely controlled mobile interference device designed primarily for interference (jamming) and immunity testing of wireless sensors operating in the 2.4 GHz band (Wi-Fi). The main idea was to build a remotely controlled test device to test the immunity of wireless sensors operating in the 2.4 GHz band directly in field conditions. The remotely controlled mobile interference device is equipped with a special interference apparatus, using a special magnetron tube as a source of interference. Magnetron was selected due to its high performance, allowing interference with wireless sensors over long distances. As magnetron is powered by high voltage (3 kVDC) and is being used in a remotely controlled device, it was important to solve the issue of its power supply using an accumulator. The remotely controlled device was further equipped with the option of detecting and analysing signals in the frequency band of 1 GHz to 18 GHz, adding an extra operational mode that can be used in civil (commercial), industrial, and military applications. Detection and analysis of extraneous signals that may affect our various electronic devices, operating in the 1 GHz to 18 GHz frequency band, is very important. By detecting and analyzing the detected signal, it is possible to recognize what kind of foreign device is transmitting on the detected frequency and how much it can affect the proper functioning of our electronic devices. All the individual parts of the remotely controlled mobile interference device are described in this article in detail, including their optimization for maximum use of the accumulator capacity by which the remotely controlled mobile interference device is powered. A substantial part of this article is devoted to optimizing the interference apparatus power supply with a resonant converter and internal intelligence, where the accumulators’ capacity is measured to gain needed predictions for maximum use of Li-Po batteries and thus extending its time of use.