Polymer-coated silica nanoparticles (PSiNPs) have been experimentally investigated in core- and micro-scale studies for enhanced oil recovery (EOR). Wettability and flow rate have a considerable effect on oil displacement in porous media. This work investigates the efficiency of PSiNPs for oil recovery on micro-scale at three wettability states (water-wet, intermediate-wet, and oil-wet). In addition, a cluster mobilization regime is considered in all experiments. A microfluidic approach was utilized to perform flooding experiments with constant experimental settings such as flowrate, pore-structure, initial oil topology, porosity, and permeability. In this study, the wettability of the microfluidic chips was altered to have three states of wettability. Firstly, a micro-scale study (brine-oil-glass system) of each wettability condition effect on flow behavior was conducted via monitoring dynamic changes in the oleic phase. Secondly, the obtained results were used as a basis to understand the changes induced by the PSiNPs while flooding at the same conditions. The experimental data were extracted by means of image processing and analysis at a high spatial and temporal resolution. Low injection rate experiments (corresponding to ~1.26 m/day in reservoir) in a brine-oil-glass system showed that the waterflood invaded with a more stable front with a slower displacement velocity in the water-wet state compared to the other states, which had water channeling through the big pores. As a result, a faster stop of the dynamic changes for the intermediate- and oil-wet state was observed, leading to lower oil recoveries compared to the water-wet state. In a cluster mobilization regime, dynamic changes were noticeable only for the oil-wet condition. For the aforementioned different conditions, PSiNPs improved oil displacement efficiency. The usage of PSiNPs showed a better clusterization efficiency, leading to a higher mobilization, smaller remaining oil clusters, and lower connectivity of the residual oil. The knowledge from this experimental work adds to the understanding of the behavior of polymer-coated silica nanoparticles as a recovery agent at different wettability states and a cluster mobilization regime.
17 April 2023 in Journal of Energy Resources Technology
The use of geopolymers as a full replacement for cement in oil well cementing applications requires the development of not only environmentally friendly but also user-friendly cementitious materials. This study aims to investigate the early-age mechanical and chemical properties of synthesized one-part geopolymers, which are heat-cured rock-based products. These geopolymers were synthesized from granite-based precursors and were activated by solid powders of potassium silicate, with a small portion of potassium hydroxide (KOH) as an accelerator to enhance the setting time and early strength. The mechanical and chemical properties of the one-part geopolymers were characterized, and the mineralogy of the solidified samples was analyzed through crystallography to better understand their microstructure. The study found that the investigated one-part geopolymer mixes, which were activated by a solid activator with a modulus ratio of 2.4, developed acceptable compressive strength of around 7 to 13 MPa within 24 h and up to 7 days. The use of one-part geopolymers has the potential to provide environmentally- and user-friendly slurries that can facilitate their utilization for large-scale in-situ applications in the petroleum and civil engineering sectors.
Nanotechnology is one of the modern techniques that can be used for enhancing the oil recovery. Enhanced oil recovery (EOR) is mainly used after oil production declination by chemically altering the injection water. However, it is very important to have an environmentally friendly method to enhance oil recovery. A possible method is to use nanofluids that include nanosilica-polymer (NFs) which contain mainly sandstone ingredients. This research is mainly an experimental investigation of the usage of several nanofluids with silica particles for enhanced oil recovery. Nanofluid injection is performed in core plugs and the oil recovery is compared with the oil recovery obtained with synthetic sea water (SSW) injection. Both nanofluid and SSW are injected in secondary mode. Five cleaned and dried Berea sandstone cores were used in the core flooding experiments. First, secondary recovery was applied on all cores by SSW injection. Then the cores were re-cleaned and re-dryed to be prepared for the secondary recovery by using 4 different types of nanofluids with the same concentration of 0.1 wt% as NFs. In this research, it was important to use exactly the same rock in both the SSW and nanofluid flooding to avoid any effect of pore structure on the oil recovery. The research showed that the best nanofluid contained nanoparticles of silica-alumina. This nanofluid gave the highest oil recovery and altered the wettability from water wet to strongly water wet due to the ionic interactions. The ultimate oil recovery was increased to 10.4% of OOIP (original oil in place) compared to SSW injection. In addition to investigating the quantitative effect of the use of several nanofluids with different nanoparticles sizes and surface modifications on oil recovery we also applied Scanning Electron Microscopy (SEM) to study pore blockage, log jamming, and emulsions between NFs and crude oil.
The main objective of this research is to present two new approaches for unconventional gas reservoirs rock typing methods. In our rock typing we automatically adjust rock type classes by optimization routines using specific surface area per unit grain volume and volume of kerogen values. Further, our results are compared to other conventional rock typing methods. The presented methos can enhance unconventional reservoir characterization by developing and/or establishing new correlations. This is exemplified through a real case study of an unconventional shale gas reservoir called Upper Safa formation that is located in the western desert of Egypt. Addition we describe the fluid properties more consistently through a full integration of unconventional rock parameters such as surface roughness factor, gas adsorption, type of kerogen, volume of kerogen, level of maturity and total organic carbon content. The Upper Safa formation is a shale gas unconventional resource play. Interpretation analysis has confirmed the hydrocarbon potential in the Upper Safa formation. Geochemical pyrolysis analysis has been used to confirm the presents of Kerogen type III. Total organic carbon content results are obtained within the ranges of very good petroleum potential according to Rock Eval pyrolysis from 2% to 4% TOC. The Upper Safa formation is a highly heterogeneous formation, with the Dykstra Parson permeability variation giving a heterogeneity value close to 100%. Large variation in the permeability, rangeing from milli-Darcy to nano-Darcy, is common for unconventional shale reservoirs. This large variation in permeability complicates rock typing of the reservoar. Several conventional rock typing methods have been applied to for the zonation problem, including as Amaefule, Discrete rock typing, Flow Zone Indicator, permeability predictive model, Winland, and a modified Winland. For comparison of the different methods, they have all been forced to produce the same number of rock classes. We have established routines for optimal selection of the boundary values distinguishing these rock classes. We also present two new rock typing techniques utilizing specific surface area per unit grain volume and TOC values.